RCC-02-03 Chapter 02 · Analysis and Design of Beams in Flexure

Flanged Beams — T-Beams & L-Beams in Flexure (IS 456:2000)

Subject
Reinforced Concrete Structures (RCC)
Chapter
02 — Analysis and Design of Beams in Flexure
Prerequisites
Singly Reinforced Rectangular Beams (RCC-02-01), Doubly Reinforced Beams (RCC-02-02), Stress Block Derivation (RCC-01-03).
Target Examinations
GATE CE, UPSC ESE, SSC JE, State AE, RRB JE, State JE
Master Directory
civil_/notes/reinforced_cement_concrete/02_analysis_and_design_of_beams_in_flexure/03_flanged_beams_t_and_l_beams.md
In this chapter (3 topics)
On this page
  1. 1. Introduction & Structural Action of Flanged Beams
  2. Key Engineering Advantages of Flanged Beams:
  3. 2. Shear Lag Phenomenon & Effective Flange Width (bf)
  4. 2.1 The Concept of Effective Flange Width (bf)
  5. 2.2 IS 456:2000 Codified Formulas for bf (Clause 23.1.2)
  6. 3. Case 1: Neutral Axis Lies Within the Flange (xu ≤ Df)
  7. 3.1 Mathematical Formulations for Case 1
  8. 4. Case 2A: Neutral Axis in Web with Shallow Flange (xu > Df and Df ≤ frac37 xu)
  9. 4.1 Physical Criterion for Shallow Flange
  10. 4.2 Compressive Forces & Neutral Axis Formulation
  11. 4.3 Moment of Resistance (Mu)
  12. 5. Case 2B: Neutral Axis in Web with Deep Flange (xu > Df and Df > frac37 xu)
  13. 5.1 The IS 456 Annex G Equivalent Thickness Factor (yf)
  14. 5.2 Compressive Equilibrium & Neutral Axis Depth (xu)
  15. 5.3 Moment of Resistance (Mu)
  16. 5.4 Limiting Moment of Resistance (Mu,lim) for Deep Flanged Beams
  17. 6. Inverted T-Beam Action & Negative Moment Behavior at Continuous Supports
  18. 7. Systematic Analysis Algorithm for Flanged Beams
  19. 8. Worked Numerical Examples
  20. Problem 1: Analysis of T-Beam with Neutral Axis in Flange (Case 1)
  21. Problem 2: Analysis of T-Beam with NA in Web — Shallow Flange (Case 2A)
  22. Problem 3: Analysis of T-Beam with NA in Web — Deep Flange (Case 2B with yf)
  23. 9. Common Misconceptions & Exam Pitfalls
  24. 10. Comparative Summary & Master Formula Sheet
  25. Master Formulations for Flanged Beams
  26. 11. Practice Questions & Competitive Examination Problems
  27. Question 1 (GATE CE — 1 Mark)
  28. Question 2 (UPSC ESE — Objective)
  29. Question 3 (SSC JE — Technical)
  30. Question 4 (State AE — Analytical)
  31. Question 5 (GATE CE — 2 Marks)
  32. Question 6 (UPSC ESE — Conventional)
  33. 12. References & Code Standards

1. Introduction & Structural Action of Flanged Beams

In typical cast-in-place reinforced concrete construction, floor slabs and supporting beams are cast monolithically. Under positive (sagging) bending moments—such as in the middle of a simply supported or continuous span—the top fibers of the beam are in compression while the bottom fibers are in tension.

Because the slab is cast integrally with the beam, a portion of the slab on either side of the beam web acts as a wide compression flange, while the narrow beam below the slab functions as the web (or rib) to resist shear and house the longitudinal tension reinforcement.

  • T-Beams: Formed at interior bays where the slab extends continuously on both sides of the web.
  • L-Beams (Inverted L / Spandrel Beams): Formed at exterior perimeter edges where the slab extends on only one side of the web.
+----------------------------------------------------------------------------------------------------+
|                                 MONOLITHIC BEAM-SLAB FLOOR SYSTEM                                  |
+----------------------------------------------------------------------------------------------------+
|                                                                                                    |
|    |<-- b1/2 -->|                   |<------ b ------>|                   |<-- b2/2 -->|           |
|    +------------+-------------------+-----------------+-------------------+------------+  ---      |
|    |            |                   |                 |                   |            |   | Df    |
|    |            |      SLAB         |   TOP FLANGE    |      SLAB         |            |   |       |
|    +-----+------+-------------------+--------+--------+-------------------+------+-----+  ---      |
|          |                                   |                                   |                 |
|          | L-BEAM                            | T-BEAM                            | L-BEAM          |
|          | (Perimeter)                       | (Interior)                        | (Perimeter)     |
|          |                                   |                                   |                 |
|          |<--bw-->|                          |<--bw-->|                          |<--bw-->|        |
|          +--------+                          +--------+                          +--------+        |
+----------------------------------------------------------------------------------------------------+

Key Engineering Advantages of Flanged Beams:

  1. Massive Compressive Capacity: The wide top slab provides an immense compression area, ensuring that singly reinforced flanged beams rarely crush in compression.
  2. Material Economy: Concrete in the cracked tension zone is eliminated, significantly reducing the dead weight of the floor system compared to a solid rectangular beam of width bfb_f.
  3. Enhanced Deflection Rigidity: Flanged beams exhibit substantial flexural stiffness (EIE I), reducing service load deflections across long spans.

2. Shear Lag Phenomenon & Effective Flange Width (bfb_f)

In elementary beam theory, bending normal stress is assumed uniform across the entire width of a cross-section. However, in wide-flanged RC beams, compressive forces are introduced into the slab exclusively through the beam web. The compressive stress is transmitted outward into the slab flange via in-plane horizontal shear stresses.

Because the slab possesses finite in-plane shear stiffness, the longitudinal compressive strain lags behind with increasing distance from the web. Consequently:

  • Compressive stress is maximum directly over the web.
  • Compressive stress decays non-linearly toward the outer edges of the slab overhang.

This phenomenon is known as Shear Lag.

Flanged Beam Geometry, Shear Lag and Effective Width

2.1 The Concept of Effective Flange Width (bfb_f)

To avoid complex 3D non-linear stress integration in practical engineering, the actual non-uniform compressive stress profile across the full slab width (bb) is replaced by an idealized, equivalent uniform compressive stress acting over a reduced width called the Effective Flange Width (bfb_f):

∫−b/2b/2σ(y) dy=σmax⁡⋅bf\int_{-b/2}^{b/2} \sigma(y) \, dy = \sigma_{\max} \cdot b_f

2.2 IS 456:2000 Codified Formulas for bfb_f (Clause 23.1.2)

1. Monolithic / Continuous T-Beams (Clause 23.1.2 a):

bf=l06+bw+6 Df≤b\mathbf{b_f = \frac{l_0}{6} + b_w + 6 \, D_f} \quad \le b

2. Monolithic / Continuous L-Beams (Clause 23.1.2 b):

bf=l012+bw+3 Df≤bw+clear span between beams2\mathbf{b_f = \frac{l_0}{12} + b_w + 3 \, D_f} \quad \le b_w + \frac{\text{clear span between beams}}{2}

3. Isolated T-Beams (Clause 23.1.2 c):

For beams where the flange is not part of a continuous floor slab (e.g., precast girders, isolated footbridges):

bf=l0l0b+4+bw≤b\mathbf{b_f = \frac{l_0}{\frac{l_0}{b} + 4} + b_w} \quad \le b

4. Isolated L-Beams (Clause 23.1.2 c):

bf=0.5 l0l0b+4+bw≤b\mathbf{b_f = \frac{0.5 \, l_0}{\frac{l_0}{b} + 4} + b_w} \quad \le b

Where:

  • bfb_f: Effective width of flange (mm\text{mm}).
  • bwb_w: Width of web / rib (mm\text{mm}).
  • DfD_f: Thickness of flange / slab depth (mm\text{mm}).
  • bb: Actual width of the flange (center-to-center distance between adjacent bays).
  • l0l_0: Distance between points of zero bending moment along the span:
    • For Simply Supported Beams: l0=Leffl_0 = L_{\text{eff}} (effective span).
    • For Continuous Intermediate Spans: l0=0.70 Leffl_0 = 0.70 \, L_{\text{eff}}.
    • For Continuous End Spans: l0=0.85 Leffl_0 = 0.85 \, L_{\text{eff}}.

3. Case 1: Neutral Axis Lies Within the Flange (xu≤Dfx_u \le D_f)

When the amount of tension reinforcement is moderate or the effective flange width is large, the neutral axis falls completely within the slab flange (xu≤Dfx_u \le D_f).

Because concrete below the neutral axis is in tension and completely neglected in flexural calculations, the concrete compression zone is a simple rectangle of width bfb_f and depth xux_u. The overhangs outside the web below the neutral axis are already cracked, so whether they exist or not has zero effect on the internal stress block!

When xu≤Df  ⟹  The Flanged Beam behaves exactly as a Rectangular Beam of width b=bf\mathbf{\text{When } x_u \le D_f \implies \text{The Flanged Beam behaves exactly as a Rectangular Beam of width } b = b_f}
   <------------------------ bf ------------------------>
   +----------------------------------------------------+  ---
   |             COMPRESSION ZONE (CONCRETE)            |   |
   |              Uniform Width = bf                    |   | xu <= Df
---+----------------------------------------------------+---+--- NA (eps = 0)
   |  . . . . . . . . . . . . . . . . . . . . . . . . . |   | Df
   +--------------------+          +--------------------+  ---
                        |          |
                        |   WEB    |
                        |  CRACKED |
                        | (O)  (O) |
                        |<-- bw -->|

3.1 Mathematical Formulations for Case 1

  1. Actual Neutral Axis Depth (xux_u):

    C=T  ⟹  0.36 fck bf xu=0.87 fy AstC = T \implies 0.36 \, f_{ck} \, b_f \, x_u = 0.87 \, f_y \, A_{st} xu=0.87 fy Ast0.36 fck bf\mathbf{x_u = \frac{0.87 \, f_y \, A_{st}}{0.36 \, f_{ck} \, b_f}}
  2. Verification Condition: Check if xu≤Dfx_u \le D_f. If true, Case 1 is confirmed.

  3. Limiting Neutral Axis Depth (xu,max⁡x_{u,\max}):

    xu,max⁡=k⋅d(k=0.53 for Fe 250,0.48 for Fe 415,0.46 for Fe 500)x_{u,\max} = k \cdot d \quad (k = 0.53 \text{ for Fe 250}, 0.48 \text{ for Fe 415}, 0.46 \text{ for Fe 500})
  4. Moment of Resistance (MuM_u):

    • For an Under-Reinforced Section (xu<xu,max⁡x_u < x_{u,\max}): Mu=0.87 fy Ast d(1−fy Astfck bf d)=0.36 fck bf xu(d−0.42 xu)\mathbf{M_u = 0.87 \, f_y \, A_{st} \, d \left( 1 - \frac{f_y \, A_{st}}{f_{ck} \, b_f \, d} \right) = 0.36 \, f_{ck} \, b_f \, x_u (d - 0.42 \, x_u)}
    • For a Balanced Section (xu=xu,max⁡x_u = x_{u,\max}): Mu,lim⁡=Qlim⁡ fck bf d2\mathbf{M_{u,\lim} = Q_{\lim} \, f_{ck} \, b_f \, d^2}

4. Case 2A: Neutral Axis in Web with Shallow Flange (xu>Dfx_u > D_f and Df≤37xuD_f \le \frac{3}{7} x_u)

When tension reinforcement is heavy, the neutral axis crosses the flange-web junction and enters the web (xu>Dfx_u > D_f). The compression zone now forms a T-shaped area.

To evaluate capacity, the T-shaped compression zone is divided into two distinct components:

  1. The Web Component: A rectangular column of concrete of width bwb_w and depth xux_u.
  2. The Flange Overhang Component: Two symmetrical flange projections of combined width (bf−bw)(b_f - b_w) and thickness DfD_f.
Flanged Beam Stress Blocks and Analysis Cases

4.1 Physical Criterion for Shallow Flange

In RCC-01-03, we proved that the IS 456 parabolic-rectangular stress block maintains a constant uniform stress of 0.4467fck≈0.45fck0.4467 f_{ck} \approx 0.45 f_{ck} from the top fiber down to depth z=37xu≈0.43xuz = \frac{3}{7} x_u \approx 0.43 x_u.

Therefore, when:

Df≤37 xu(or approximately Dfd≤0.2)\mathbf{D_f \le \frac{3}{7} \, x_u \quad \left( \text{or approximately } \frac{D_f}{d} \le 0.2 \right)}

the entire thickness of the flange overhang falls within the constant rectangular stress plateau! The compressive stress across the entire flange overhang is uniform and equal to 0.447fck0.447 f_{ck}.

4.2 Compressive Forces & Neutral Axis Formulation

  • Web Compressive Force (CwC_w): Cw=0.36 fck bw xuC_w = 0.36 \, f_{ck} \, b_w \, x_u acting at depth yˉw=0.42xu\bar{y}_w = 0.42 x_u from the top fiber (lever arm zw=d−0.42xuz_w = d - 0.42 x_u).
  • Flange Overhang Compressive Force (CfC_f): Cf=0.4467 fck(bf−bw)DfC_f = 0.4467 \, f_{ck} (b_f - b_w) D_f acting at the midthickness of the flange yˉf=Df/2\bar{y}_f = D_f / 2 (lever arm zf=d−0.5Dfz_f = d - 0.5 D_f).

Equating total compression to total tension (Cw+Cf=TC_w + C_f = T):

0.36 fck bw xu+0.447 fck(bf−bw)Df=0.87 fy Ast0.36 \, f_{ck} \, b_w \, x_u + 0.447 \, f_{ck} (b_f - b_w) D_f = 0.87 \, f_y \, A_{st}

Solving for the Actual Neutral Axis Depth (xux_u):

xu=0.87 fy Ast−0.447 fck(bf−bw)Df0.36 fck bw\mathbf{x_u = \frac{0.87 \, f_y \, A_{st} - 0.447 \, f_{ck} (b_f - b_w) D_f}{0.36 \, f_{ck} \, b_w}}

4.3 Moment of Resistance (MuM_u)

Taking moments of internal compressive forces about the tension reinforcement:

Mu=0.36 fck bw xu(d−0.42 xu)+0.447 fck(bf−bw)Df(d−0.5 Df)\mathbf{M_u = 0.36 \, f_{ck} \, b_w \, x_u (d - 0.42 \, x_u) + 0.447 \, f_{ck} (b_f - b_w) D_f (d - 0.5 \, D_f)}

5. Case 2B: Neutral Axis in Web with Deep Flange (xu>Dfx_u > D_f and Df>37xuD_f > \frac{3}{7} x_u)

When the flange is relatively thick compared to the neutral axis depth (Df>37xuD_f > \frac{3}{7} x_u):

  • The upper portion of the flange overhang (down to 37xu\frac{3}{7} x_u) experiences uniform stress 0.447fck0.447 f_{ck}.
  • The lower portion of the flange overhang (from 37xu\frac{3}{7} x_u down to DfD_f) falls into the parabolic stress region, where stress drops parabolically toward the neutral axis.

5.1 The IS 456 Annex G Equivalent Thickness Factor (yfy_f)

To avoid integrating parabolic stress over the flange overhangs, IS 456:2000 Clause G-2.2.1 replaces the true non-uniform stress profile over depth DfD_f with an equivalent uniform stress block of magnitude 0.447fck0.447 f_{ck} acting over an Equivalent Flange Depth (yfy_f):

yf=0.15 xu+0.65 Df≤Df\mathbf{y_f = 0.15 \, x_u + 0.65 \, D_f \quad \le D_f}

The flange overhang compressive force is then:

Cf=0.447 fck(bf−bw) yf\mathbf{C_f = 0.447 \, f_{ck} (b_f - b_w) \, y_f}

acting at centroid depth yˉf=yf/2\bar{y}_f = y_f / 2 from the top fiber (lever arm zf=d−0.5yfz_f = d - 0.5 y_f).

5.2 Compressive Equilibrium & Neutral Axis Depth (xux_u)

Equating Cw+Cf=TC_w + C_f = T:

0.36 fck bw xu+0.447 fck(bf−bw)[0.15 xu+0.65 Df]=0.87 fy Ast0.36 \, f_{ck} \, b_w \, x_u + 0.447 \, f_{ck} (b_f - b_w) [0.15 \, x_u + 0.65 \, D_f] = 0.87 \, f_y \, A_{st}

Rearranging to solve explicitly for xux_u:

xu[0.36 fck bw+0.067 fck(bf−bw)]=0.87 fy Ast−0.291 fck(bf−bw)Dfx_u \left[ 0.36 \, f_{ck} \, b_w + 0.067 \, f_{ck} (b_f - b_w) \right] = 0.87 \, f_y \, A_{st} - 0.291 \, f_{ck} (b_f - b_w) D_f xu=0.87 fy Ast−0.447 fck(bf−bw)(0.65 Df)0.36 fck bw+0.447 fck(bf−bw)(0.15)\mathbf{x_u = \frac{0.87 \, f_y \, A_{st} - 0.447 \, f_{ck} (b_f - b_w) (0.65 \, D_f)}{0.36 \, f_{ck} \, b_w + 0.447 \, f_{ck} (b_f - b_w) (0.15)}}

5.3 Moment of Resistance (MuM_u)

Mu=0.36 fck bw xu(d−0.42 xu)+0.447 fck(bf−bw)yf(d−0.5 yf)\mathbf{M_u = 0.36 \, f_{ck} \, b_w \, x_u (d - 0.42 \, x_u) + 0.447 \, f_{ck} (b_f - b_w) y_f (d - 0.5 \, y_f)}

5.4 Limiting Moment of Resistance (Mu,lim⁡M_{u,\lim}) for Deep Flanged Beams

When xu=xu,max⁡x_u = x_{u,\max}:

yf=0.15 xu,max⁡+0.65 Df≤Dfy_f = 0.15 \, x_{u,\max} + 0.65 \, D_f \quad \le D_f Mu,lim⁡=0.36 fck bw xu,max⁡(d−0.42 xu,max⁡)+0.447 fck(bf−bw)yf(d−0.5 yf)\mathbf{M_{u,\lim} = 0.36 \, f_{ck} \, b_w \, x_{u,\max} (d - 0.42 \, x_{u,\max}) + 0.447 \, f_{ck} (b_f - b_w) y_f (d - 0.5 \, y_f)}

6. Inverted T-Beam Action & Negative Moment Behavior at Continuous Supports

One of the most vital practical concepts in structural concrete design concerns the behavior of continuous flanged beams over interior columns and continuous supports:

  1. Moment Reversal (Hogging Bending Moments): Over interior supports, continuous beams experience negative bending moments (tension at the top, compression at the bottom).
  2. Top Flange in Tension: The wide top slab flange is situated on the tension side. Since concrete in tension micro-cracks and is neglected in strength calculations, the wide flange contributes ZERO compressive resistance!
  3. Compression Confined to Narrow Web: Compressive stress is resisted entirely by the bottom of the beam, which has a narrow width of only bwb_w.

[!IMPORTANT] GOVERNING STRUCTURAL RULE (IS 456 Clause 23.1.1):
At continuous supports subjected to negative (hogging) bending moments, T-beams and L-beams MUST be designed as RECTANGULAR BEAMS of width b=bwb = b_w!
Because bwb_w is narrow, the section frequently becomes over-reinforced unless its depth is very large; hence, flanged beams over continuous supports are almost universally designed as doubly reinforced rectangular sections (b=bwb = b_w) with compression steel placed in the bottom of the web.


7. Systematic Analysis Algorithm for Flanged Beams

+----------------------------------------------------------------------------------------------------+
|                                    FLANGED BEAM ANALYSIS ALGORITHM                                 |
+----------------------------------------------------------------------------------------------------+
|                                                                                                    |
|   Step 1: Compute Effective Flange Width (bf) per IS 456 Clause 23.1.2:                            |
|           bf = l0/6 + bw + 6 Df  (for T-beam)  or  l0/12 + bw + 3 Df  (for L-beam)                |
|                                                                                                    |
|   Step 2: Trial Neutral Axis Calculation (Assume NA lies within Flange):                           |
|           xu,trial = (0.87 * fy * Ast) / (0.36 * fck * bf)                                         |
|                                                                                                    |
|   Step 3: Classify Neutral Axis Position:                                                          |
|           - IF xu,trial <= Df --> [CASE 1: NA IN FLANGE]                                           |
|             Adopt xu = xu,trial. Check xu <= xu,max.                                               |
|             Mu = 0.87 * fy * Ast * d * [1 - (fy * Ast) / (fck * bf * d)]                          |
|                                                                                                    |
|           - IF xu,trial > Df  --> [CASE 2: NA IN WEB]                                              |
|             Proceed to Step 4.                                                                     |
|                                                                                                    |
|   Step 4: Sub-classify Flange Depth (Check Df vs 3/7 xu):                                          |
|           - Assume Df <= 3/7 xu [CASE 2A: SHALLOW FLANGE]:                                         |
|             Compute Cf = 0.447 * fck * (bf - bw) * Df                                              |
|             Compute xu = [0.87 * fy * Ast - Cf] / (0.36 * fck * bw)                                 |
|             Verify if Df <= (3/7) * xu. If verified, Case 2A holds:                                |
|             Mu = 0.36*fck*bw*xu*(d - 0.42*xu) + Cf*(d - 0.5*Df)                                    |
|                                                                                                    |
|           - If Df > (3/7) * xu [CASE 2B: DEEP FLANGE]:                                             |
|             Compute yf = 0.15 * xu + 0.65 * Df                                                     |
|             Solve for xu using equivalent yf equation.                                             |
|             Compute Cf = 0.447 * fck * (bf - bw) * yf                                              |
|             Mu = 0.36*fck*bw*xu*(d - 0.42*xu) + Cf*(d - 0.5*yf)                                    |
|                                                                                                    |
|   Step 5: Cap Moment Capacity if xu > xu,max:                                                      |
|           If xu > xu,max, cap at Mu,lim using xu,max in place of xu.                               |
+----------------------------------------------------------------------------------------------------+

8. Worked Numerical Examples

Problem 1: Analysis of T-Beam with Neutral Axis in Flange (Case 1)

Problem Statement:
An interior simply supported T-beam has an effective flange width bf=1200 mmb_f = 1200\text{ mm}, flange thickness Df=100 mmD_f = 100\text{ mm}, web width bw=250 mmb_w = 250\text{ mm}, and effective depth d=450 mmd = 450\text{ mm}. Concrete grade is M20 (fck=20 N/mm2f_{ck} = 20\text{ N/mm}^2) and steel grade is Fe 415 (fy=415 N/mm2f_y = 415\text{ N/mm}^2). The tension reinforcement consists of 44 bars of 20 mm20\text{ mm} diameter (Ast=1256.64 mm2A_{st} = 1256.64\text{ mm}^2).

  1. Determine the actual depth of the neutral axis (xux_u).
  2. Verify whether the neutral axis lies in the flange or web.
  3. Calculate the ultimate factored moment of resistance (MuM_u).

Step-by-Step Solution:

Part 1: Trial Neutral Axis in Flange Assume neutral axis lies within the flange (xu≤Dfx_u \le D_f):

xu=0.87 fy Ast0.36 fck bf=0.87×415×1256.640.36×20×1200=453,709.878640=52.51 mmx_u = \frac{0.87 \, f_y \, A_{st}}{0.36 \, f_{ck} \, b_f} = \frac{0.87 \times 415 \times 1256.64}{0.36 \times 20 \times 1200} = \frac{453,709.87}{8640} = \mathbf{52.51 \, mm}

Part 2: Location Verification & Section Classification

  • Since xu=52.51 mm≤Df=100.0 mmx_u = 52.51\text{ mm} \le D_f = 100.0\text{ mm}, the assumption is verified: NA lies within the flange (Case 1).
  • Limiting neutral axis depth for Fe 415: xu,max⁡=0.48⋅d=0.48×450=216.00 mmx_{u,\max} = 0.48 \cdot d = 0.48 \times 450 = \mathbf{216.00 \, mm}
  • Since xu=52.51 mm<xu,max⁡=216.00 mmx_u = 52.51\text{ mm} < x_{u,\max} = 216.00\text{ mm}, the section is UNDER-REINFORCED.

Part 3: Ultimate Moment of Resistance (MuM_u) The beam behaves as a rectangular section of width b=bf=1200 mmb = b_f = 1200\text{ mm}:

Mu=0.87 fy Ast d(1−fy Astfck bf d)M_u = 0.87 \, f_y \, A_{st} \, d \left( 1 - \frac{f_y \, A_{st}}{f_{ck} \, b_f \, d} \right) fy Astfck bf d=415×1256.6420×1200×450=521,505.610,800,000=0.048288\frac{f_y \, A_{st}}{f_{ck} \, b_f \, d} = \frac{415 \times 1256.64}{20 \times 1200 \times 450} = \frac{521,505.6}{10,800,000} = 0.048288 Mu=(0.87×415×1256.64×450)×(1−0.048288)×10−6M_u = (0.87 \times 415 \times 1256.64 \times 450) \times (1 - 0.048288) \times 10^{-6} Mu=204.169×0.951712=194.310 kNmM_u = 204.169 \times 0.951712 = \mathbf{194.310 \, kNm}

(Using lever arm method: z=450−0.42(52.51)=427.95 mm  ⟹  Mu=453.710×0.42795=194.162 kNmz = 450 - 0.42(52.51) = 427.95\text{ mm} \implies M_u = 453.710 \times 0.42795 = \mathbf{194.162 \, kNm}).


Problem 2: Analysis of T-Beam with NA in Web — Shallow Flange (Case 2A)

Problem Statement:
A T-beam has bf=1000 mmb_f = 1000\text{ mm}, bw=300 mmb_w = 300\text{ mm}, d=500 mmd = 500\text{ mm}, and flange depth Df=75 mmD_f = 75\text{ mm}. Concrete grade is M20 (fck=20 N/mm2f_{ck} = 20\text{ N/mm}^2) and steel grade is Fe 415 (fy=415 N/mm2f_y = 415\text{ N/mm}^2). The tension reinforcement consists of 55 bars of 25 mm25\text{ mm} diameter (Ast=2454.37 mm2A_{st} = 2454.37\text{ mm}^2). Compute the actual neutral axis depth and the ultimate moment of resistance.

Step-by-Step Solution:

Part 1: Check if NA is in Flange

xu,trial=0.87×415×2454.370.36×20×1000=886,150.37200=123.08 mm>Df=75 mmx_{u,\text{trial}} = \frac{0.87 \times 415 \times 2454.37}{0.36 \times 20 \times 1000} = \frac{886,150.3}{7200} = 123.08\text{ mm} > D_f = 75\text{ mm}

Therefore, the neutral axis lies in the web (Case 2).

Part 2: Check Shallow vs Deep Flange Condition (Df≤37xuD_f \le \frac{3}{7} x_u) Assume the flange is shallow (Df≤37xuD_f \le \frac{3}{7} x_u):

  • Flange overhang compressive force: Cf=0.447 fck(bf−bw)Df=0.447×20×(1000−300)×75=0.447×20×700×75=469,350 N=469.35 kNC_f = 0.447 \, f_{ck} (b_f - b_w) D_f = 0.447 \times 20 \times (1000 - 300) \times 75 = 0.447 \times 20 \times 700 \times 75 = \mathbf{469,350 \, N} = \mathbf{469.35 \, kN}
  • Compute xux_u from web equilibrium: xu=0.87 fy Ast−Cf0.36 fck bw=886,150.3−469,350.00.36×20×300=416,800.32160=192.96 mmx_u = \frac{0.87 \, f_y \, A_{st} - C_f}{0.36 \, f_{ck} \, b_w} = \frac{886,150.3 - 469,350.0}{0.36 \times 20 \times 300} = \frac{416,800.3}{2160} = \mathbf{192.96 \, mm}
  • Check condition: 37xu=37×192.96=82.70 mm\frac{3}{7} x_u = \frac{3}{7} \times 192.96 = \mathbf{82.70 \, mm} Since Df=75.0 mm≤37xu=82.70 mmD_f = 75.0\text{ mm} \le \frac{3}{7} x_u = 82.70\text{ mm}, the shallow flange assumption (Case 2A) is strictly verified.
  • Check limiting neutral axis: xu,max⁡=0.48×500=240.00 mmx_{u,\max} = 0.48 \times 500 = \mathbf{240.00 \, mm} Since xu=192.96 mm<xu,max⁡=240.00 mmx_u = 192.96\text{ mm} < x_{u,\max} = 240.00\text{ mm}, the section is under-reinforced.

Part 3: Ultimate Moment of Resistance (MuM_u)

  • Moment from web component: Muw=0.36 fck bw xu(d−0.42 xu)=0.36×20×300×192.96×[500−0.42(192.96)]×10−6M_{uw} = 0.36 \, f_{ck} \, b_w \, x_u (d - 0.42 \, x_u) = 0.36 \times 20 \times 300 \times 192.96 \times [500 - 0.42(192.96)] \times 10^{-6} Muw=416.794×[500−81.04]×10−3=416.794×418.96×10−3=174.621 kNmM_{uw} = 416.794 \times [500 - 81.04] \times 10^{-3} = 416.794 \times 418.96 \times 10^{-3} = \mathbf{174.621 \, kNm}
  • Moment from flange overhang component: Muf=Cf(d−0.5 Df)=469.350×(500−0.5×75)×10−3=469.350×462.50×10−3=217.074 kNmM_{uf} = C_f (d - 0.5 \, D_f) = 469.350 \times (500 - 0.5 \times 75) \times 10^{-3} = 469.350 \times 462.50 \times 10^{-3} = \mathbf{217.074 \, kNm}
  • Total Ultimate Moment Capacity (MuM_u): Mu=Muw+Muf=174.621+217.074=391.695 kNmM_u = M_{uw} + M_{uf} = 174.621 + 217.074 = \mathbf{391.695 \, kNm}

Problem 3: Analysis of T-Beam with NA in Web — Deep Flange (Case 2B with yfy_f)

Problem Statement:
An isolated T-beam girder has bf=800 mmb_f = 800\text{ mm}, bw=250 mmb_w = 250\text{ mm}, d=400 mmd = 400\text{ mm}, and flange thickness Df=120 mmD_f = 120\text{ mm}. Concrete grade is M25 (fck=25 N/mm2f_{ck} = 25\text{ N/mm}^2) and steel grade is Fe 500 (fy=500 N/mm2f_y = 500\text{ N/mm}^2). Tension steel area provided is Ast=2000 mm2A_{st} = 2000\text{ mm}^2. Determine the neutral axis depth using the IS 456 Annex G yfy_f formulation and calculate the ultimate moment capacity.

Step-by-Step Solution:

Part 1: Check NA Position

xu,trial=0.87×500×20000.36×25×800=870,0007200=120.83 mm>Df=120 mmx_{u,\text{trial}} = \frac{0.87 \times 500 \times 2000}{0.36 \times 25 \times 800} = \frac{870,000}{7200} = 120.83\text{ mm} > D_f = 120\text{ mm}

The neutral axis extends slightly below the flange into the web. Notice that 37xu≈37(121)=51.86 mm≪Df=120 mm\frac{3}{7} x_u \approx \frac{3}{7} (121) = 51.86\text{ mm} \ll D_f = 120\text{ mm}.
Hence, the flange is DEEP (Df>37xuD_f > \frac{3}{7} x_u), requiring the yfy_f formulation (Case 2B).

Part 2: Formulation with Equivalent Flange Depth yfy_f Per IS 456 Clause G-2.2.1:

yf=0.15 xu+0.65 Df=0.15 xu+0.65(120)=0.15 xu+78.0y_f = 0.15 \, x_u + 0.65 \, D_f = 0.15 \, x_u + 0.65(120) = 0.15 \, x_u + 78.0

Axial equilibrium:

0.36 fck bw xu+0.447 fck(bf−bw) yf=0.87 fy Ast0.36 \, f_{ck} \, b_w \, x_u + 0.447 \, f_{ck} (b_f - b_w) \, y_f = 0.87 \, f_y \, A_{st} 0.36(25)(250)xu+0.447(25)(800−250)[0.15xu+78.0]=0.87(500)(2000)0.36(25)(250) x_u + 0.447(25)(800 - 250) [0.15 x_u + 78.0] = 0.87(500)(2000) 2250 xu+6146.25[0.15xu+78.0]=870,0002250 \, x_u + 6146.25 [0.15 x_u + 78.0] = 870,000 2250 xu+921.94 xu+479,407.50=870,0002250 \, x_u + 921.94 \, x_u + 479,407.50 = 870,000 3171.94 xu=390,592.50  ⟹  xu=123.14 mm3171.94 \, x_u = 390,592.50 \implies x_u = \mathbf{123.14 \, mm}
  • Verify yfy_f: yf=0.15(123.14)+78.0=18.47+78.0=96.47 mm≤Df=120 mm(Valid)y_f = 0.15(123.14) + 78.0 = 18.47 + 78.0 = \mathbf{96.47 \, mm} \le D_f = 120 \, mm \quad \text{(Valid)}
  • Limiting depth of neutral axis for Fe 500: xu,max⁡=0.46⋅d=0.46×400=184.00 mmx_{u,\max} = 0.46 \cdot d = 0.46 \times 400 = \mathbf{184.00 \, mm} Since xu=123.14 mm<xu,max⁡=184.00 mmx_u = 123.14\text{ mm} < x_{u,\max} = 184.00\text{ mm}, the section is under-reinforced.

Part 3: Ultimate Moment of Resistance (MuM_u)

  • Web component: Muw=0.36×25×250×123.14×[400−0.42(123.14)]×10−6M_{uw} = 0.36 \times 25 \times 250 \times 123.14 \times [400 - 0.42(123.14)] \times 10^{-6} Muw=277.065×[400−51.72]×10−3=277.065×348.28×10−3=96.497 kNmM_{uw} = 277.065 \times [400 - 51.72] \times 10^{-3} = 277.065 \times 348.28 \times 10^{-3} = \mathbf{96.497 \, kNm}
  • Flange overhang component: Cf=0.447×25×550×96.47=592,936 N=592.936 kNC_f = 0.447 \times 25 \times 550 \times 96.47 = \mathbf{592,936 \, N} = \mathbf{592.936 \, kN} Muf=Cf(d−0.5 yf)=592.936×[400−0.5(96.47)]×10−3=592.936×351.765×10−3=208.573 kNmM_{uf} = C_f (d - 0.5 \, y_f) = 592.936 \times [400 - 0.5(96.47)] \times 10^{-3} = 592.936 \times 351.765 \times 10^{-3} = \mathbf{208.573 \, kNm}
  • Total Ultimate Moment Capacity (MuM_u): Mu=Muw+Muf=96.497+208.573=305.070 kNmM_u = M_{uw} + M_{uf} = 96.497 + 208.573 = \mathbf{305.070 \, kNm}

9. Common Misconceptions & Exam Pitfalls

[!WARNING] Pitfall 1: Using Effective Flange Width (bfb_f) in Continuous Support Hogging Bending
Students frequently design the support section of a continuous T-beam using bfb_f. Over interior supports, negative bending moments induce tension in the slab; concrete cracks and is neglected. The beam must strictly be analyzed as a rectangular beam of width b=bwb = b_w.

[!WARNING] Pitfall 2: Forgetting to Check whether Df≤37xuD_f \le \frac{3}{7} x_u when NA is in Web
In many competitive exam problems where xu>Dfx_u > D_f, students erroneously use DfD_f in the moment equation without verifying whether Df≤37xuD_f \le \frac{3}{7} x_u. If Df>37xuD_f > \frac{3}{7} x_u, the equivalent depth yf=0.15xu+0.65Dfy_f = 0.15 x_u + 0.65 D_f must be used. Omitting yfy_f causes significant numerical errors.

[!CAUTION] Pitfall 3: Neglecting the Code Upper Bound on bfb_f
The codified formula bf=l0/6+bw+6Dfb_f = l_0/6 + b_w + 6 D_f can sometimes evaluate to a number greater than the actual center-to-center bay spacing bb. Remember that bfb_f is always capped at the actual physical spacing bb.

[!IMPORTANT] Pitfall 4: Misapplying the Isolated Beam Formula
The formula for isolated T-beams (bf=l0l0/b+4+bwb_f = \frac{l_0}{l_0/b + 4} + b_w) is fundamentally different from the continuous beam formula. Be careful to check whether the problem specifies an "isolated" girder or a "monolithic floor slab" beam.


10. Comparative Summary & Master Formula Sheet

Master Formulations for Flanged Beams

Parameter Governing Mathematical Formula Remarks / Code Reference
Continuous T-Beam bfb_f bf=l06+bw+6 Df≤bb_f = \frac{l_0}{6} + b_w + 6 \, D_f \le b IS 456 Clause 23.1.2(a)
Continuous L-Beam bfb_f bf=l012+bw+3 Df≤bb_f = \frac{l_0}{12} + b_w + 3 \, D_f \le b IS 456 Clause 23.1.2(b)
Isolated T-Beam bfb_f bf=l0l0b+4+bw≤bb_f = \frac{l_0}{\frac{l_0}{b} + 4} + b_w \le b IS 456 Clause 23.1.2(c)
Zero Moment Distance l0l_0 l0=Leffl_0 = L_{\text{eff}} (Simply Supported) | 0.70Leff0.70 L_{\text{eff}} (Continuous) Effective inflection length
Case 1 NA (xu≤Dfx_u \le D_f) xu=0.87fyAst0.36fckbfx_u = \frac{0.87 f_y A_{st}}{0.36 f_{ck} b_f} Rectangular beam of width bfb_f
Case 1 Moment (MuM_u) Mu=0.87fyAstd[1−(fyAst)/(fckbfd)]M_u = 0.87 f_y A_{st} d [1 - (f_y A_{st})/(f_{ck} b_f d)] Rectangular beam formula
Case 2A NA (Df≤37xuD_f \le \frac{3}{7} x_u) xu=0.87fyAst−0.447fck(bf−bw)Df0.36fckbwx_u = \frac{0.87 f_y A_{st} - 0.447 f_{ck} (b_f - b_w) D_f}{0.36 f_{ck} b_w} Uniform flange stress block
Case 2A Moment (MuM_u) Mu=0.36fckbwxu(d−0.42xu)+0.447fck(bf−bw)Df(d−0.5Df)M_u = 0.36 f_{ck} b_w x_u (d - 0.42 x_u) + 0.447 f_{ck} (b_f - b_w) D_f (d - 0.5 D_f) Lever arms: d−0.42xud - 0.42x_u and d−0.5Dfd - 0.5D_f
Equivalent Flange Depth (yfy_f) yf=0.15 xu+0.65 Df≤Dfy_f = 0.15 \, x_u + 0.65 \, D_f \le D_f IS 456 Annex G Eq. G-2.2.1
Case 2B Moment (MuM_u) Mu=0.36fckbwxu(d−0.42xu)+0.447fck(bf−bw)yf(d−0.5yf)M_u = 0.36 f_{ck} b_w x_u (d - 0.42 x_u) + 0.447 f_{ck} (b_f - b_w) y_f (d - 0.5 y_f) Deep flange with yfy_f
Support Section (Hogging) b=bwb = b_w (Top flange in tension ignored) Designed as rectangular beam (bwb_w)

11. Practice Questions & Competitive Examination Problems

Question 1 (GATE CE — 1 Mark)

A monolithic reinforced concrete floor system has a continuous T-beam with effective span 6.0 m6.0\text{ m}, web width 300 mm300\text{ mm}, and slab depth 120 mm120\text{ mm}. If the actual center-to-center distance between beams is 3.0 m3.0\text{ m}, the effective flange width bfb_f of an intermediate continuous span as per IS 456:2000 is:

  • (A) 1720 mm1720\text{ mm}
  • (B) 1600 mm1600\text{ mm}
  • (C) 2020 mm2020\text{ mm}
  • (D) 3000 mm3000\text{ mm}
    Answer: (A)
    Explanation: For intermediate continuous span, l0=0.70Leff=0.70×6000=4200 mml_0 = 0.70 L_{\text{eff}} = 0.70 \times 6000 = 4200\text{ mm}.
    bf=l06+bw+6Df=42006+300+6(120)=700+300+720=1720 mm≤3000 mmb_f = \frac{l_0}{6} + b_w + 6 D_f = \frac{4200}{6} + 300 + 6(120) = 700 + 300 + 720 = 1720\text{ mm} \le 3000\text{ mm}.

Question 2 (UPSC ESE — Objective)

In a reinforced concrete T-beam subjected to sagging bending moments, if the depth of the neutral axis xux_u is less than the flange thickness DfD_f, the section is analyzed as:

  • (A) A rectangular beam of width equal to web width bwb_w
  • (B) A rectangular beam of width equal to effective flange width bfb_f
  • (C) A flanged section using the equivalent flange thickness yfy_f
  • (D) A doubly reinforced section
    Answer: (B)
    Explanation: Concrete below the neutral axis is in tension and neglected; hence the compressive zone is a pure rectangle of width bfb_f and depth xux_u.

Question 3 (SSC JE — Technical)

For an isolated T-beam with effective span l0=6 ml_0 = 6\text{ m}, actual flange width b=1000 mmb = 1000\text{ mm}, and web width bw=300 mmb_w = 300\text{ mm}, the effective flange width bfb_f as per IS 456:2000 is:

  • (A) 900 mm900\text{ mm}
  • (B) 1000 mm1000\text{ mm}
  • (C) 800 mm800\text{ mm}
  • (D) 600 mm600\text{ mm}
    Answer: (A)
    Explanation: bf=l0l0b+4+bw=600060001000+4+300=60006+4+300=600010+300=600+300=900 mm≤1000 mmb_f = \frac{l_0}{\frac{l_0}{b} + 4} + b_w = \frac{6000}{\frac{6000}{1000} + 4} + 300 = \frac{6000}{6 + 4} + 300 = \frac{6000}{10} + 300 = 600 + 300 = 900\text{ mm} \le 1000\text{ mm}.

Question 4 (State AE — Analytical)

In the limit state analysis of a flanged beam having xu>Dfx_u > D_f and Df>37xuD_f > \frac{3}{7} x_u, the equivalent depth of flange yfy_f specified by IS 456:2000 Annex G is:

  • (A) 0.65xu+0.15Df0.65 x_u + 0.15 D_f
  • (B) 0.15xu+0.65Df0.15 x_u + 0.65 D_f
  • (C) 0.42xu+0.58Df0.42 x_u + 0.58 D_f
  • (D) 0.50xu+0.50Df0.50 x_u + 0.50 D_f
    Answer: (B)
    Explanation: Clause G-2.2.1 specifies yf=0.15xu+0.65Df≤Dfy_f = 0.15 x_u + 0.65 D_f \le D_f.

Question 5 (GATE CE — 2 Marks)

At the interior support of a continuous reinforced concrete T-beam, the cross-section is subjected to a factored hogging moment of 220 kNm220\text{ kNm}. The beam dimensions are bf=1200 mm,Df=120 mm,bw=250 mm,d=450 mmb_f = 1200\text{ mm}, D_f = 120\text{ mm}, b_w = 250\text{ mm}, d = 450\text{ mm}. Concrete grade is M20 (fck=20 MPaf_{ck} = 20\text{ MPa}) and steel is Fe 415 (fy=415 MPaf_y = 415\text{ MPa}). The limiting moment of resistance (Mu,lim⁡M_{u,\lim}) available from the concrete in compression at this support is:

  • (A) 670.68 kNm670.68\text{ kNm}
  • (B) 139.73 kNm139.73\text{ kNm}
  • (C) 220.00 kNm220.00\text{ kNm}
  • (D) 113.18 kNm113.18\text{ kNm}
    Answer: (B)
    Explanation: Under hogging moment, the top flange is in tension and ignored; compression is resisted strictly by the web (b=bw=250 mmb = b_w = 250\text{ mm}).
    Mu,lim⁡=0.138fckbwd2=0.138×20×250×(450)2×10−6=139.725 kNmM_{u,\lim} = 0.138 f_{ck} b_w d^2 = 0.138 \times 20 \times 250 \times (450)^2 \times 10^{-6} = 139.725\text{ kNm}.

Question 6 (UPSC ESE — Conventional)

Derive the expression for the ultimate moment of resistance of a T-beam when the neutral axis lies in the web and the flange is shallow (Df≤37xuD_f \le \frac{3}{7} x_u).
Answer Summary: Decompose the compression zone into a web rectangle (bw×xub_w \times x_u) and flange overhangs [(bf−bw)×Df(b_f - b_w) \times D_f]. The web force is Cw=0.36fckbwxuC_w = 0.36 f_{ck} b_w x_u acting at lever arm d−0.42xud - 0.42 x_u. Because Df≤37xuD_f \le \frac{3}{7} x_u, the flange overhangs fall entirely in the uniform stress plateau 0.447fck0.447 f_{ck}, giving force Cf=0.447fck(bf−bw)DfC_f = 0.447 f_{ck} (b_f - b_w) D_f acting at lever arm d−0.5Dfd - 0.5 D_f. Summing moments: Mu=0.36fckbwxu(d−0.42xu)+0.447fck(bf−bw)Df(d−0.5Df)M_u = 0.36 f_{ck} b_w x_u (d - 0.42 x_u) + 0.447 f_{ck} (b_f - b_w) D_f (d - 0.5 D_f).


12. References & Code Standards

  1. IS 456:2000 (Reaffirmed 2021): Plain and Reinforced Concrete — Code of Practice, Section 3 (Clause 23: General Design Considerations, Clause 23.1.2: Effective Flange Width, Annex G: Clause G-2: Flanged Sections).
  2. SP:16 (1980): Design Aids for Reinforced Concrete to IS: 456-1978, Bureau of Indian Standards, New Delhi.
  3. Pillai, S. U., & Menon, D. (2021): Reinforced Concrete Design, 4th Edition, McGraw-Hill Education, India.
  4. Varghese, P. C. (2009): Limit State Design of Reinforced Concrete, 2nd Edition, PHI Learning Pvt. Ltd., New Delhi.
  5. Jain, A. K. (2012): Reinforced Concrete: Limit State Design, 7th Edition, Nem Chand & Bros, Roorkee.