STEEL-06-01 Chapter 06 · Plastic Analysis

Plastic Hinge Fundamentals, Shape Factors & Plastic Modulus (IS 800:2007 Section 8)

In this chapter (4 topics)
On this page
  1. 1. Executive Summary & Code Hierarchy
  2. 2. Material Assumptions & Idealized Stress-Strain Models
  3. 2.1 Idealized Elasto-Plastic Stress-Strain Curve
  4. 2.2 Statutory Ductility Requirements for Plastic Design (IS 800 Cl. 8.1.1)
  5. 3. Moment-Curvature (M-φ) Relationship & Cross-Section Plastification
  6. Stage 1: Purely Elastic (M < My)
  7. Stage 2: Inception of Yielding (M = My)
  8. Stage 3: Elasto-Plastic Yield Penetration (My < M < Mp)
  9. Stage 4: Fully Plastic State & Plastic Hinge (M = Mp)
  10. 4. Equal Area Theorem & Plastic Neutral Axis (PNA)
  11. Crucial Distinction: PNA vs ENA
  12. 5. Plastic Section Modulus (Zp) & Shape Factor (S)
  13. 5.1 Definition of Plastic Section Modulus Zp
  14. 5.2 The Shape Factor (S)
  15. 5.3 The Load Factor (λL)
  16. 6. Complete Mathematical Derivation of Shape Factors for Key Cross-Sections
  17. 1. Rectangular Section (b × d)
  18. 2. Solid Circular Section of Diameter D
  19. 3. Diamond / Rhombus with Vertical Diagonal d and Width b
  20. 4. Triangular Section (Base b, Height h, Axis Parallel to Base)
  21. 5. Thin Circular Ring / Pipe (Radius R, Thickness t ll R)
  22. 6. Standard Rolled I-Section (ISMB / ISWB)
  23. 7. Plastic Hinge Mechanics & Length of Plastic Hinge (Lp)
  24. Case 1: Simply Supported Beam with Concentrated Central Load W
  25. Case 2: Simply Supported Beam with Uniformly Distributed Load w
  26. 8. SVG Engineering Visualizations
  27. FIGURE STEEL-06-01A: Plastic Hinge Mechanics & Moment-Curvature (M-φ)
  28. FIGURE STEEL-06-01B: Shape Factors & Plastic Hinge Length (Lp)
  29. 9. Complete Step-by-Step Mathematical Derivations
  30. Derivation 1: Exact Elastic Core Depth & Inelastic Moment Equation
  31. Derivation 2: Triangle Shape Factor Integration
  32. 10. Multi-Exam Comprehensive Solved Examples
  33. Example 1: Unsymmetrical Built-Up Tee Section Plastic Properties (GATE CE / ESE Conventional)
  34. Example 2: Length of Plastic Hinge for 4 Structural Shapes
  35. Example 3: Partially Plastified Rectangular Beam — Elastic Core Depth, Inelastic Bending Moment & Residual Stress Distribution
  36. 11. Exam Traps, Common Pitfalls & Code Nuances
  37. Trap 1: Confusing ENA and PNA in Asymmetric Sections
  38. Trap 2: Memorizing Shape Factors Inverted
  39. Trap 3: Direct Comparison of Profile Plastic Efficiencies
  40. Trap 4: Plastic Hinge Formula Inversion for Point Load vs UDL
  41. 12. Official Exam Practice Questions
  42. Question 1 (GATE CE)
  43. Question 2 (UPSC ESE)
  44. Question 3 (SSC JE)
  45. Question 4 (State AE / RRB JE)
  46. Question 5 (UPSC ESE Conventional)

1. Executive Summary & Code Hierarchy

In conventional elastic design (Working Stress Method or elastic limit state), a structural steel member is considered to reach its ultimate limit when the stress at the extreme outermost fiber reaches the yield strength fyf_y (the Yield Moment My=fy⋅ZeM_y = f_y \cdot Z_e). However, mild structural steel is an extraordinarily ductile crystalline material: yielding of the outermost fibers does not precipitate collapse. Instead, as the bending moment increases beyond MyM_y, inner fibers progressively yield until the entire cross-section yields in either tension or compression.

At this fully plastic state, the section develops its Fully Plastic Moment Capacity (Mp=fy⋅ZpM_p = f_y \cdot Z_p) and behaves as a Plastic Hinge—a localized physical zone capable of undergoing substantial plastic rotation at constant moment resistance MpM_p, dissipating immense mechanical energy.

Plastic analysis and design provides a realistic, physically verified assessment of the ultimate collapse load of redundant structural steel frameworks. Governed by:

  • IS 800:2007 (Section 8): Indian Standard General Construction in Steel — Code of Practice (Third Revision), Section 8: Plastic Design.
  • IS 800:2007 Cl. 8.2: Design of Members Subjected to Bending (Class 1 Plastic and Class 2 Compact Sections).
  • AISC 360-16 (Appendix 1): Inelastic Analysis and Design.
  • Eurocode 3 (EN 1993-1-1 Cl. 5.6 & Cl. 6.2.5): Plastic analysis and cross-sectional resistance.
┌───────────────────────────────────────────────────────────────────────────────────┐
│                      KEY PLASTIC DESIGN PARAMETERS                                │
├───────────────────────────────────────────────────────────────────────────────────┤
│ 1. Yield Moment (M_y):                                                            │
│    M_y = fy · Z_e (Onset of yielding at extreme fiber)                            │
│                                                                                   │
│ 2. Fully Plastic Moment (M_p):                                                    │
│    M_p = fy · Z_p (Entire cross-section yields in tension and compression)        │
│                                                                                   │
│ 3. Shape Factor (S):                                                              │
│    S = M_p / M_y = Z_p / Z_e ≥ 1.0 (Geometric reserve strength above yield)       │
│                                                                                   │
│ 4. Load Factor (λ_L):                                                             │
│    λ_L = Collapse Load / Working Load = (Factor of Safety) · S                    │
│                                                                                   │
│ 5. Plastic Neutral Axis (PNA):                                                    │
│    Equal Area Axis (A_tension = A_compression = A / 2) under pure bending         │
└───────────────────────────────────────────────────────────────────────────────────┘

2. Material Assumptions & Idealized Stress-Strain Models

2.1 Idealized Elasto-Plastic Stress-Strain Curve

To make plastic theory mathematically tractable without sacrificing physical accuracy, the stress-strain curve of structural mild steel is idealized as an Elasto-Plastic (Prandtl) model:

σ=E⋅ϵfor ϵ≤ϵy(Linear Elastic Region)σ=fyfor ϵy<ϵ≤ϵst(Perfect Plastic Plateau)\begin{aligned} \sigma &= E \cdot \epsilon \quad \text{for } \epsilon \le \epsilon_y \quad (\text{Linear Elastic Region}) \\ \sigma &= f_y \quad \text{for } \epsilon_y < \epsilon \le \epsilon_{st} \quad (\text{Perfect Plastic Plateau}) \end{aligned}

where:

  • E=2×105 MPaE = 2 \times 10^5\text{ MPa} is Young's modulus of elasticity.
  • ϵy=fy/E≈0.00125\epsilon_y = f_y / E \approx 0.00125 (for fy=250 MPaf_y = 250\text{ MPa}).
  • ϵst≈10 to 15ϵy\epsilon_{st} \approx 10\text{ to }15 \epsilon_y is the strain at the onset of strain hardening.
  • ϵu≥0.15 to 0.20\epsilon_u \ge 0.15\text{ to }0.20 is the ultimate fracture strain.

2.2 Statutory Ductility Requirements for Plastic Design (IS 800 Cl. 8.1.1)

Plastic analysis relies entirely on the premise that plastic hinges can rotate through large angles without premature local buckling, web crippling, or brittle fracture. Consequently, IS 800:2007 permits plastic design ONLY IF the structural steel satisfies all three conditions:

  1. The yield ratio is limited: fyfu≤0.85\frac{f_y}{f_u} \le 0.85
  2. The elongation at failure on a standard gauge length is: δu≥15%\delta_u \ge 15\%
  3. The ductility ratio μd\mu_d satisfies: μd=ϵuϵy≥6.0\mu_d = \frac{\epsilon_u}{\epsilon_y} \ge 6.0

Standard structural mild steel (such as IS 2062 Grade E250) has ϵu/ϵy≈120 to 160\epsilon_u / \epsilon_y \approx 120\text{ to }160, vastly exceeding the statutory minimum of 6.06.0.


3. Moment-Curvature (M−ϕM-\phi) Relationship & Cross-Section Plastification

Consider a symmetrical beam cross-section subjected to an increasing bending moment MM. As the load increases from zero to collapse, the beam passes through four distinct physical regimes:

    STAGE 1:               STAGE 2:               STAGE 3:               STAGE 4:
    Elastic (M < My)       Yield Inception        Elasto-Plastic         Fully Plastic (Mp)
    Linear σ < fy          Extreme fiber = fy     Plastic penetration    Rectangular blocks
         ▲                      ▲                      ▲                      ▲
        /│                     /│                     ┌┴┐                    ┌┴┐
       / │                    / │                     │ │                    │ │
      /  │                   /  │                     │ │                    │ │
     /   │                  /   │                     │ │                    │ │
    ─────┼─────            ─────┼─────            ────┼─┼────            ────┼─┼──── PNA
         │\                     │ \                   │ │                    │ │
         │ \                    │  \                  │ │                    │ │
         │  \                   │   \                 │ │                    │ │
         │   \                  │    \                └┬┘                    └┬┘
         ▼                      ▼                      ▼                      ▼

Stage 1: Purely Elastic (M<MyM < M_y)

  • The normal stress σ\sigma varies linearly across the depth according to Navier's flexural formula: σ=M⋅yI\sigma = \frac{M \cdot y}{I}
  • The maximum extreme fiber stress is less than yield: σmax⁡<fy\sigma_{\max} < f_y.
  • Curvature is linear: ϕ=MEI\phi = \frac{M}{E I}.

Stage 2: Inception of Yielding (M=MyM = M_y)

  • Yielding initiates at the outermost tensile and compressive fibers simultaneously: σmax⁡=fy\sigma_{\max} = f_y
  • The moment at this instant is the Yield Moment (MyM_y): My=fy⋅ZeM_y = f_y \cdot Z_e where Ze=I/ymax⁡Z_e = I / y_{\max} is the elastic section modulus.
  • The corresponding yield curvature is: ϕy=MyEI=fyE⋅ymax⁡\phi_y = \frac{M_y}{E I} = \frac{f_y}{E \cdot y_{\max}}

Stage 3: Elasto-Plastic Yield Penetration (My<M<MpM_y < M < M_p)

  • As the moment increases beyond MyM_y, outer fibers cannot take more stress than fyf_y and flow plastically.
  • Yielding penetrates inward toward the neutral axis, creating an elastic core of depth 2y02 y_0 centered on the neutral axis, sandwiched between outer plastic yield blocks.
  • Within the elastic core (−y0≤y≤y0-y_0 \le y \le y_0): σ(y)=fy(yy0)\sigma(y) = f_y \left(\frac{y}{y_0}\right)
  • In the plastic zones (∣y∣>y0|y| > y_0): σ(y)=±fy\sigma(y) = \pm f_y
  • For a rectangular section (b×db \times d), the moment at this intermediate stage is: M=fy[bd24−by023]=Mp[1−13(2y0d)2]M = f_y \left[ \frac{b d^2}{4} - \frac{b y_0^2}{3} \right] = M_p \left[ 1 - \frac{1}{3} \left(\frac{2 y_0}{d}\right)^2 \right]
  • The curvature ϕ\phi is given by: ϕ=ϵyy0=ϕy(d/2y0)\phi = \frac{\epsilon_y}{y_0} = \phi_y \left(\frac{d / 2}{y_0}\right) Rearranging in terms of MM: M=Mp[1−13(ϕyϕ)2]M = M_p \left[ 1 - \frac{1}{3} \left(\frac{\phi_y}{\phi}\right)^2 \right]

Stage 4: Fully Plastic State & Plastic Hinge (M=MpM = M_p)

  • As curvature ϕ→∞\phi \to \infty, the elastic core depth approaches zero (y0→0y_0 \to 0).
  • The entire cross-section yields: every fiber is stressed to either +fy+f_y in compression or −fy-f_y in tension.
  • The cross-section reaches its absolute maximum capacity: the Fully Plastic Moment Capacity (MpM_p): Mp=fy⋅ZpM_p = f_y \cdot Z_p where ZpZ_p is the Plastic Section Modulus.
  • The physical cross-section transforms into a Plastic Hinge: it can rotate indefinitely at the constant internal moment MpM_p.

4. Equal Area Theorem & Plastic Neutral Axis (PNA)

Under pure bending, there is zero net axial force acting on the cross-section (N=0N = 0).

  1. Integrating the fully plastic stress distribution across the entire cross-sectional area: ∫Aσ dA=∫Ac(+fy) dA+∫At(−fy) dA=0\int_A \sigma \, dA = \int_{A_c} (+f_y) \, dA + \int_{A_t} (-f_y) \, dA = 0 fyAc−fyAt=0  ⟹  Ac=Atf_y A_c - f_y A_t = 0 \implies A_c = A_t
  2. Since Ac+At=AtotalA_c + A_t = A_{total}: Ac=At=Atotal2A_c = A_t = \frac{A_{total}}{2}
EQUAL AREA THEOREM:\mathbf{EQUAL\ AREA\ THEOREM:} Under pure bending, the Plastic Neutral Axis (PNA) divides the cross-sectional area into two EQUAL halves.\textit{Under pure bending, the Plastic Neutral Axis (PNA) divides the cross-sectional area into two EQUAL halves.}

Crucial Distinction: PNA vs ENA

ParameterElastic Neutral Axis (ENA)Plastic Neutral Axis (PNA)DefinitionFirst moment of area is zero: ∫y dA=0Equal area dividing line: Ac=At=A/2Physical LocationCentroidal Axis of the geometric shapeEqual Area AxisSymmetrical SectionsIdentical to PNA (at mid-depth)Identical to ENA (at mid-depth)Unsymmetrical SectionsDiffers from PNA!Differs from ENA!\begin{array}{|l|l|l|} \hline \textbf{Parameter} & \textbf{Elastic Neutral Axis (ENA)} & \textbf{Plastic Neutral Axis (PNA)} \\ \hline \textbf{Definition} & \text{First moment of area is zero: } \int y \, dA = 0 & \text{Equal area dividing line: } A_c = A_t = A/2 \\ \textbf{Physical Location} & \textbf{Centroidal Axis} \text{ of the geometric shape} & \textbf{Equal Area Axis} \\ \textbf{Symmetrical Sections} & \text{Identical to PNA (at mid-depth)} & \text{Identical to ENA (at mid-depth)} \\ \textbf{Unsymmetrical Sections} & \textbf{Differs from PNA!} & \textbf{Differs from ENA!} \\ \hline \end{array}

Example (T-Section): In an unsymmetrical T-section with a heavy flange, the centroid (ENA) lies near the junction of flange and web. However, the equal-area divider (PNA) frequently lies inside the flange plate itself!


5. Plastic Section Modulus (ZpZ_p) & Shape Factor (SS)

5.1 Definition of Plastic Section Modulus ZpZ_p

The internal resisting couple of the fully plastic cross-section is the sum of the moments of the compressive and tensile stress blocks about the Plastic Neutral Axis:

Mp=C⋅yˉc+T⋅yˉt=(Acfy)yˉc+(Atfy)yˉtM_p = C \cdot \bar{y}_c + T \cdot \bar{y}_t = (A_c f_y) \bar{y}_c + (A_t f_y) \bar{y}_t

Since Ac=At=A/2A_c = A_t = A / 2:

Mp=fy⋅[A2(yˉc+yˉt)]=fy⋅ZpM_p = f_y \cdot \left[ \frac{A}{2} (\bar{y}_c + \bar{y}_t) \right] = f_y \cdot Z_p Zp=A2(yˉc+yˉt)=Acyˉc+AtyˉtZ_p = \frac{A}{2} (\bar{y}_c + \bar{y}_t) = A_c \bar{y}_c + A_t \bar{y}_t

where yˉc\bar{y}_c and yˉt\bar{y}_t are the distances from the PNA to the centroids of the compression and tension areas, respectively.

5.2 The Shape Factor (SS)

The Shape Factor SS of a cross-section is the non-dimensional ratio of its fully plastic moment capacity to its yield moment capacity:

S=MpMy=fy⋅Zpfy⋅Ze=ZpZe≥1.0S = \frac{M_p}{M_y} = \frac{f_y \cdot Z_p}{f_y \cdot Z_e} = \frac{Z_p}{Z_e} \ge 1.0

Physical Interpretation: The Shape Factor represents the percentage reserve strength inherent in the cross-section between first yield at the extreme fiber and total plastic collapse:

Plastic Reserve Strength=(S−1.0)×100%\text{Plastic Reserve Strength} = (S - 1.0) \times 100\%

5.3 The Load Factor (λL\lambda_L)

In plastic design, the Load Factor λL\lambda_L is the ratio of the collapse load WcW_c to the working (service) load WwW_w:

λL=WcWw=MpMw=MpMy/FOS=FOS⋅(MpMy)=FOS⋅S\lambda_L = \frac{W_c}{W_w} = \frac{M_p}{M_w} = \frac{M_p}{M_y / \text{FOS}} = \text{FOS} \cdot \left(\frac{M_p}{M_y}\right) = \text{FOS} \cdot S

where FOS\text{FOS} is the traditional factor of safety against yield (≈1.50 to 1.67\approx 1.50\text{ to }1.67).


6. Complete Mathematical Derivation of Shape Factors for Key Cross-Sections

1. Rectangular Section (b×db \times d)

  • Area A=bdA = b d.
  • Neutral axis at d/2d/2: Ac=At=bd/2A_c = A_t = b d / 2.
  • Centroids: yˉc=yˉt=d/4\bar{y}_c = \bar{y}_t = d / 4.
  • Plastic modulus: Zp=bd2(d4+d4)=bd24Z_p = \frac{b d}{2} \left( \frac{d}{4} + \frac{d}{4} \right) = \frac{b d^2}{4}
  • Elastic modulus: Ze=bd26Z_e = \frac{b d^2}{6}
  • Shape Factor: S=ZpZe=bd2/4bd2/6=64=1.500S = \frac{Z_p}{Z_e} = \frac{b d^2 / 4}{b d^2 / 6} = \frac{6}{4} = \mathbf{1.500}
  • Reserve strength: +50%+50\% beyond elastic yield.

2. Solid Circular Section of Diameter DD

  • Area A=πD2/4A = \pi D^2 / 4.
  • Neutral axis at mid-diameter (R=D/2R = D/2): Ac=At=πD28A_c = A_t = \frac{\pi D^2}{8}.
  • Centroid of a semicircle from diameter: yˉc=yˉt=4R3π=4(D/2)3π=2D3π\bar{y}_c = \bar{y}_t = \frac{4 R}{3 \pi} = \frac{4 (D/2)}{3 \pi} = \frac{2 D}{3 \pi}
  • Plastic modulus: Zp=2(πD28⋅2D3π)=D36Z_p = 2 \left( \frac{\pi D^2}{8} \cdot \frac{2 D}{3 \pi} \right) = \frac{D^3}{6}
  • Elastic modulus: Ze=πD332Z_e = \frac{\pi D^3}{32}
  • Shape Factor: S=ZpZe=D3/6πD3/32=326π=163π=1.6977≈1.70S = \frac{Z_p}{Z_e} = \frac{D^3 / 6}{\pi D^3 / 32} = \frac{32}{6 \pi} = \frac{16}{3 \pi} = \mathbf{1.6977 \approx 1.70}
  • Reserve strength: +69.8%+69.8\% beyond elastic yield.

3. Diamond / Rhombus with Vertical Diagonal dd and Width bb

  • Area A=12bdA = \frac{1}{2} b d.
  • PNA at mid-height (d/2d/2): Ac=At=bd4A_c = A_t = \frac{b d}{4} (each is a triangle of base bb and height d/2d/2).
  • Centroid of a triangle from base: yˉc=yˉt=13(d2)=d6\bar{y}_c = \bar{y}_t = \frac{1}{3} \left(\frac{d}{2}\right) = \frac{d}{6}
  • Plastic modulus: Zp=2(bd4⋅d6)=bd212Z_p = 2 \left( \frac{b d}{4} \cdot \frac{d}{6} \right) = \frac{b d^2}{12}
  • Elastic moment of inertia: I=2(b(d/2)312)=bd348  ⟹  Ze=Id/2=bd224I = 2 \left( \frac{b (d/2)^3}{12} \right) = \frac{b d^3}{48} \implies Z_e = \frac{I}{d/2} = \frac{b d^2}{24}
  • Shape Factor: S=ZpZe=bd2/12bd2/24=2.000S = \frac{Z_p}{Z_e} = \frac{b d^2 / 12}{b d^2 / 24} = \mathbf{2.000}
  • Reserve strength: +100%+100\% (plastic capacity is exactly double the yield capacity!).

4. Triangular Section (Base bb, Height hh, Axis Parallel to Base)

  • Elastic Neutral Axis (ENA) is at h/3h/3 from base: ymax⁡=2h/3y_{\max} = 2h/3. INA=bh336  ⟹  Ze=bh3/362h/3=bh224I_{NA} = \frac{b h^3}{36} \implies Z_e = \frac{b h^3 / 36}{2 h / 3} = \frac{b h^2}{24}
  • Plastic Neutral Axis (PNA): Equal Area condition: Area of top triangle of height yp=12⋅(byph)⋅yp=byp22h=A2=bh4\text{Area of top triangle of height } y_p = \frac{1}{2} \cdot \left(b \frac{y_p}{h}\right) \cdot y_p = \frac{b y_p^2}{2 h} = \frac{A}{2} = \frac{b h}{4} yp2=h22  ⟹  yp=h2≈0.7071h(from vertex)y_p^2 = \frac{h^2}{2} \implies y_p = \frac{h}{\sqrt{2}} \approx 0.7071 h \quad (\text{from vertex})
  • Calculating plastic modulus ZpZ_p: Zp=∫∣y−yp∣ dA=bh262≈bh28.4853Z_p = \int |y - y_p| \, dA = \frac{b h^2}{6 \sqrt{2}} \approx \frac{b h^2}{8.4853}
  • Shape Factor: S=ZpZe=bh2/(62)bh2/24=2462=42=22≈2.828(if measured from apex axis)S = \frac{Z_p}{Z_e} = \frac{b h^2 / (6 \sqrt{2})}{b h^2 / 24} = \frac{24}{6 \sqrt{2}} = \frac{4}{\sqrt{2}} = 2 \sqrt{2} \approx 2.828 \quad (\text{if measured from apex axis}) (Note: For bending about the standard horizontal axis parallel to base, the exact value derived by integrating about the PNA is S=2.343S = \mathbf{2.343}).

5. Thin Circular Ring / Pipe (Radius RR, Thickness t≪Rt \ll R)

  • Area A=2πRtA = 2 \pi R t.
  • Semicircular ring area: Ac=At=πRtA_c = A_t = \pi R t.
  • Centroid of thin semicircle: yˉc=yˉt=2Rπ\bar{y}_c = \bar{y}_t = \frac{2 R}{\pi}
  • Plastic modulus: Zp=2(πRt⋅2Rπ)=4R2tZ_p = 2 \left( \pi R t \cdot \frac{2 R}{\pi} \right) = 4 R^2 t
  • Elastic modulus: Ze=πR2tZ_e = \pi R^2 t
  • Shape Factor: S=ZpZe=4R2tπR2t=4π=1.273S = \frac{Z_p}{Z_e} = \frac{4 R^2 t}{\pi R^2 t} = \frac{4}{\pi} = \mathbf{1.273}

6. Standard Rolled I-Section (ISMB / ISWB)

In an I-section, the heavy flanges are located far from the neutral axis, meaning over 80%–85%80\%\text{–}85\% of the total cross-sectional area is already located at the extreme fibers. Consequently, first yield at the extreme fiber engages nearly the entire flange, leaving very little web material to plastify:

SI−beam=1.12 to 1.18S_{I-beam} = \mathbf{1.12 \text{ to } 1.18}

(Average rule-of-thumb value used in GATE/ESE: S≈1.15S \approx 1.15).


7. Plastic Hinge Mechanics & Length of Plastic Hinge (LpL_p)

A Plastic Hinge is defined as a yielded segment of a beam where the bending moment is equal to or exceeds MyM_y, with the peak reaching MpM_p. The physical distance along the beam axis over which yielding extends is termed the Length of the Plastic Hinge (LpL_p).

  BENDING MOMENT DIAGRAM                  BEAM ELEVATION (SPREAD OF YIELD)
  
            Mp                                            W
             ▲                                            ▼
            / \                                  ═══════════════════
           /   \                                 │    Plastic Hinge│
   My ────/─────\──── My                         │    \  Yielded / │
         /       \                               │     \  Zone  /  │
        /         \                              ═══════════════════
       /           \                                   ◄── Lp ──►
      ───────────────
             ▲
             Lp (Zone where M ≥ My)

Case 1: Simply Supported Beam with Concentrated Central Load WW

  • Span =L= L. Central moment =Mp=WL/4= M_p = W L / 4.
  • The bending moment diagram is triangular, varying linearly from 00 at supports to MpM_p at midspan.
  • Let M=MyM = M_y at distance x1x_1 from the left support. By linear proportion: Myx1=MpL/2  ⟹  x1=L2(MyMp)=L2S\frac{M_y}{x_1} = \frac{M_p}{L/2} \implies x_1 = \frac{L}{2} \left(\frac{M_y}{M_p}\right) = \frac{L}{2 S}
  • The plastic hinge extends symmetrically on both sides of midspan: Lp=L−2x1=L−2(L2S)=L(1−1S)■L_p = L - 2 x_1 = L - 2 \left(\frac{L}{2 S}\right) = L \left( 1 - \frac{1}{S} \right) \quad \blacksquare
Lp FOR CONCENTRATED LOAD:Lp=L(1−1S)\mathbf{L_p\ FOR\ CONCENTRATED\ LOAD:}\quad L_p = L \left( 1 - \frac{1}{S} \right)

Evaluations for standard shapes:

  • Rectangular Beam (S=1.50S = 1.50): Lp=L(1−11.50)=L(1−23)=L3=0.333LL_p = L \left( 1 - \frac{1}{1.50} \right) = L \left( 1 - \frac{2}{3} \right) = \frac{L}{3} = \mathbf{0.333 L}
  • Diamond Beam (S=2.00S = 2.00): Lp=L(1−12.00)=L2=0.500LL_p = L \left( 1 - \frac{1}{2.00} \right) = \frac{L}{2} = \mathbf{0.500 L}
  • Rolled I-Beam (S=1.15S = 1.15): Lp=L(1−11.15)=0.130LL_p = L \left( 1 - \frac{1}{1.15} \right) = \mathbf{0.130 L}

Case 2: Simply Supported Beam with Uniformly Distributed Load ww

  • Span =L= L. Central maximum moment =Mp=wL2/8= M_p = w L^2 / 8.
  • The bending moment diagram is parabolic: M(x)=wL2x−wx22M(x) = \frac{w L}{2} x - \frac{w x^2}{2}
  • Let M=MyM = M_y at distance x1x_1 from the left support: wL2x1−wx122=My\frac{w L}{2} x_1 - \frac{w x_1^2}{2} = M_y
  • Since Mp=wL2/8  ⟹  w=8Mp/L2M_p = w L^2 / 8 \implies w = 8 M_p / L^2: 8Mp2Lx1−8Mp2L2x12=My\frac{8 M_p}{2 L} x_1 - \frac{8 M_p}{2 L^2} x_1^2 = M_y 4MpLx1−4MpL2x12=My  ⟹  4(x1L)−4(x1L)2=MyMp=1S\frac{4 M_p}{L} x_1 - \frac{4 M_p}{L^2} x_1^2 = M_y \implies 4 \left(\frac{x_1}{L}\right) - 4 \left(\frac{x_1}{L}\right)^2 = \frac{M_y}{M_p} = \frac{1}{S} 4(x1L)2−4(x1L)+1S=04 \left(\frac{x_1}{L}\right)^2 - 4 \left(\frac{x_1}{L}\right) + \frac{1}{S} = 0
  • Solving using quadratic formula: x1L=4−16−16/S8=1−1−1/S2\frac{x_1}{L} = \frac{4 - \sqrt{16 - 16 / S}}{8} = \frac{1 - \sqrt{1 - 1/S}}{2}
  • The plastic hinge length is Lp=L−2x1L_p = L - 2 x_1: Lp=L−2L[1−1−1/S2]=L1−1S■L_p = L - 2 L \left[ \frac{1 - \sqrt{1 - 1/S}}{2} \right] = L \sqrt{1 - \frac{1}{S}} \quad \blacksquare
Lp FOR UNIFORMLY DISTRIBUTED LOAD:Lp=L1−1S\mathbf{L_p\ FOR\ UNIFORMLY\ DISTRIBUTED\ LOAD:}\quad L_p = L \sqrt{1 - \frac{1}{S}}

Evaluations for standard shapes:

  • Rectangular Beam (S=1.50S = 1.50): Lp=L1−11.50=L13=L3=0.577LL_p = L \sqrt{1 - \frac{1}{1.50}} = L \sqrt{\frac{1}{3}} = \frac{L}{\sqrt{3}} = \mathbf{0.577 L}
  • Rolled I-Beam (S=1.15S = 1.15): Lp=L1−11.15=L0.1304=0.361LL_p = L \sqrt{1 - \frac{1}{1.15}} = L \sqrt{0.1304} = \mathbf{0.361 L}

Key Structural Insight: A uniformly distributed load causes a vastly longer plastic hinge zone (57.7%L57.7\% L for rectangle) than a concentrated point load (33.3%L33.3\% L) because the parabolic bending moment curve remains close to its peak over a wider distance!


8. SVG Engineering Visualizations

FIGURE STEEL-06-01A: Plastic Hinge Mechanics & Moment-Curvature (M−ϕM-\phi)

The following engineering schematic illustrates the idealized elasto-plastic stress-strain relationship, the progressive inward penetration of plasticity across a cross-section, and the non-linear asymptotic moment-curvature curve.

Plastic Hinge Mechanics and Moment Curvature

FIGURE STEEL-06-01B: Shape Factors & Plastic Hinge Length (LpL_p)

The following technical diagram details the gallery of shape factors for standard structural profiles and compares the spread of plasticity under concentrated midspan loading versus uniformly distributed loading.

Shape Factors and Plastic Hinge Length

9. Complete Step-by-Step Mathematical Derivations

Derivation 1: Exact Elastic Core Depth & Inelastic Moment Equation

Consider a rectangular cross-section of width bb and depth dd, subjected to moment MM such that My<M<MpM_y < M < M_p. Let the depth of the central elastic core be 2y02 y_0 (spanning from y=−y0y = -y_0 to y=+y0y = +y_0).

  1. In the elastic core (−y0≤y≤y0-y_0 \le y \le y_0): σ(y)=fyyy0\sigma(y) = f_y \frac{y}{y_0}
  2. In the outer plastic zones (y0<∣y∣≤d/2y_0 < |y| \le d/2): σ(y)=fy(top),σ(y)=−fy(bottom)\sigma(y) = f_y \quad (\text{top}), \quad \sigma(y) = -f_y \quad (\text{bottom})
  3. The total resisting moment is obtained by integrating across the section: M=2[∫0y0(fyyy0)(b dy)⋅y+∫y0d/2(fy)(b dy)⋅y]M = 2 \left[ \int_0^{y_0} \left(f_y \frac{y}{y_0}\right) (b \, dy) \cdot y + \int_{y_0}^{d/2} (f_y) (b \, dy) \cdot y \right]
  4. Evaluate the elastic core integral: I1=bfyy0∫0y0y2 dy=bfyy0[y033]=bfyy023I_1 = \frac{b f_y}{y_0} \int_0^{y_0} y^2 \, dy = \frac{b f_y}{y_0} \left[ \frac{y_0^3}{3} \right] = \frac{b f_y y_0^2}{3}
  5. Evaluate the plastic zone integral: I2=bfy∫y0d/2y dy=bfy[(d/2)2−y022]=bfy[d28−y022]I_2 = b f_y \int_{y_0}^{d/2} y \, dy = b f_y \left[ \frac{(d/2)^2 - y_0^2}{2} \right] = b f_y \left[ \frac{d^2}{8} - \frac{y_0^2}{2} \right]
  6. Sum the two integrals: M=2(I1+I2)=2bfy[y023+d28−y022]=2bfy[d28−y026]=fy[bd24−by023]M = 2 (I_1 + I_2) = 2 b f_y \left[ \frac{y_0^2}{3} + \frac{d^2}{8} - \frac{y_0^2}{2} \right] = 2 b f_y \left[ \frac{d^2}{8} - \frac{y_0^2}{6} \right] = f_y \left[ \frac{b d^2}{4} - \frac{b y_0^2}{3} \right]
  7. Notice that Mp=fybd24M_p = f_y \frac{b d^2}{4}. Substituting MpM_p: M=Mp[1−4y023d2]=Mp[1−13(2y0d)2]■M = M_p \left[ 1 - \frac{4 y_0^2}{3 d^2} \right] = M_p \left[ 1 - \frac{1}{3} \left(\frac{2 y_0}{d}\right)^2 \right] \quad \blacksquare

Derivation 2: Triangle Shape Factor Integration

Consider a triangle of base bb and height hh with vertex at y=0y = 0 and base at y=hy = h. The width at depth yy is w(y)=bhyw(y) = \frac{b}{h} y.

  1. Area A=12bhA = \frac{1}{2} b h. Equal area PNA is at yp=h2y_p = \frac{h}{\sqrt{2}}.
  2. Plastic section modulus is defined as the first moment of area about PNA: Zp=∫0yp(yp−y)w(y) dy+∫yph(y−yp)w(y) dyZ_p = \int_0^{y_p} (y_p - y) w(y) \, dy + \int_{y_p}^h (y - y_p) w(y) \, dy
  3. Evaluating the first integral: I1=bh∫0yp(ypy−y2) dy=bh[ypyp22−yp33]=byp36hI_1 = \frac{b}{h} \int_0^{y_p} (y_p y - y^2) \, dy = \frac{b}{h} \left[ y_p \frac{y_p^2}{2} - \frac{y_p^3}{3} \right] = \frac{b y_p^3}{6 h} Substituting yp=h/2y_p = h / \sqrt{2}: I1=b(h/2)36h=bh2122I_1 = \frac{b (h / \sqrt{2})^3}{6 h} = \frac{b h^2}{12 \sqrt{2}}
  4. Evaluating the second integral: I2=bh∫yph(y2−ypy) dy=bh[(h3−yp33)−yp(h2−yp22)]I_2 = \frac{b}{h} \int_{y_p}^h (y^2 - y_p y) \, dy = \frac{b}{h} \left[ \left(\frac{h^3 - y_p^3}{3}\right) - y_p \left(\frac{h^2 - y_p^2}{2}\right) \right] Substitute yp=h/2y_p = h / \sqrt{2}: I2=bh2h[1−1/(22)3−1/2−1/(22)2]…I_2 = \frac{b h^2}{h} \left[ \frac{1 - 1/(2\sqrt{2})}{3} - \frac{1/\sqrt{2} - 1/(2\sqrt{2})}{2} \right] \dots
  5. Summing and dividing by Ze=bh224Z_e = \frac{b h^2}{24} yields the standard closed-form shape factor: S=2.343■S = \mathbf{2.343} \quad \blacksquare

10. Multi-Exam Comprehensive Solved Examples

Example 1: Unsymmetrical Built-Up Tee Section Plastic Properties (GATE CE / ESE Conventional)

Problem Statement: A built-up structural Tee section is fabricated from Fe 410 steel (fy=250 MPaf_y = 250\text{ MPa}).

  • Flange: 200 mm200\text{ mm} wide ×20 mm\times 20\text{ mm} thick
  • Web: 15 mm15\text{ mm} thick ×180 mm\times 180\text{ mm} deep
  • Total cross-sectional depth =200 mm= 200\text{ mm}
  1. Determine the position of the Elastic Neutral Axis (ENA) and the elastic section modulus ZeZ_e.
  2. Determine the position of the Plastic Neutral Axis (PNA) and state whether it lies in the flange or the web.
  3. Compute the Plastic Section Modulus ZpZ_p and the Shape Factor SS.
  4. Calculate the yield moment MyM_y and plastic moment MpM_p.

Solution:

Step 1: Areas & Elastic Neutral Axis (ENA)

  • Flange area: Af=200×20=4000 mm2A_f = 200 \times 20 = 4000\text{ mm}^2
  • Web area: Aw=15×180=2700 mm2A_w = 15 \times 180 = 2700\text{ mm}^2
  • Total area: Atotal=4000+2700=6700 mm2A_{total} = 4000 + 2700 = \mathbf{6700\text{ mm}^2}
  • Taking moments of area about the extreme top fiber: yˉtop=Af(tf/2)+Aw(tf+dw/2)Atotal=4000(10)+2700(20+90)6700=40000+2970006700=50.30 mm\bar{y}_{top} = \frac{A_f (t_f / 2) + A_w (t_f + d_w / 2)}{A_{total}} = \frac{4000(10) + 2700(20 + 90)}{6700} = \frac{40000 + 297000}{6700} = \mathbf{50.30\text{ mm}}
  • Distance to extreme bottom fiber: yˉbot=200.0−50.30=149.70 mm\bar{y}_{bot} = 200.0 - 50.30 = \mathbf{149.70\text{ mm}} (The ENA is located 50.30 mm50.30\text{ mm} below the top of the flange).

Step 2: Moment of Inertia IxxI_{xx} & Elastic Section Modulus ZeZ_e

  • Moment of inertia about ENA using parallel axis theorem: Iflange=200×20312+4000(50.30−10)2=133,333+4000(1624.09)=6.630×106 mm4I_{flange} = \frac{200 \times 20^3}{12} + 4000(50.30 - 10)^2 = 133,333 + 4000(1624.09) = 6.630 \times 10^6\text{ mm}^4 Iweb=15×180312+2700(110−50.30)2=7,290,000+2700(3564.09)=16.913×106 mm4I_{web} = \frac{15 \times 180^3}{12} + 2700(110 - 50.30)^2 = 7,290,000 + 2700(3564.09) = 16.913 \times 10^6\text{ mm}^4 Ixx=(6.630+16.913)×106=23.543×106 mm4I_{xx} = (6.630 + 16.913) \times 10^6 = \mathbf{23.543 \times 10^6\text{ mm}^4}
  • Elastic section moduli: Ze,top=Ixxyˉtop=23.543×10650.30=468,060 mm3Z_{e,top} = \frac{I_{xx}}{\bar{y}_{top}} = \frac{23.543 \times 10^6}{50.30} = 468,060\text{ mm}^3 Ze,bot=Ixxyˉbot=23.543×106149.70=157,265 mm3Z_{e,bot} = \frac{I_{xx}}{\bar{y}_{bot}} = \frac{23.543 \times 10^6}{149.70} = 157,265\text{ mm}^3
  • The governing elastic section modulus is governed by first yield at the furthest fiber (bottom): Ze=Ze,bot=157,265 mm3Z_e = Z_{e,bot} = \mathbf{157,265\text{ mm}^3}

Step 3: Plastic Neutral Axis (PNA) - Equal Area Theorem

  • Half-area requirement: A1=A2=Atotal2=67002=3350 mm2A_1 = A_2 = \frac{A_{total}}{2} = \frac{6700}{2} = \mathbf{3350\text{ mm}^2}
  • Since the flange area alone (Af=4000 mm2A_f = 4000\text{ mm}^2) is greater than 3350 mm23350\text{ mm}^2, THE PLASTIC NEUTRAL AXIS LIES INSIDE THE FLANGE!
  • Let the PNA be located at depth ypy_p from the top surface: bf⋅yp=Atotal2  ⟹  200⋅yp=3350  ⟹  yp=3350200=16.75 mmb_f \cdot y_p = \frac{A_{total}}{2} \implies 200 \cdot y_p = 3350 \implies y_p = \frac{3350}{200} = \mathbf{16.75\text{ mm}} (The PNA is located 16.75 mm16.75\text{ mm} below the top surface, completely inside the 20 mm20\text{ mm} flange). Note the dramatic difference: ENA=50.30 mm\text{ENA} = 50.30\text{ mm} (in the web) vs PNA=16.75 mm\text{PNA} = 16.75\text{ mm} (in the flange)!

Step 4: Plastic Section Modulus ZpZ_p

  • Top compression zone (above PNA):
    • Area A1=200×16.75=3350 mm2A_1 = 200 \times 16.75 = 3350\text{ mm}^2
    • Centroid from PNA: yˉ1=16.752=8.375 mm\bar{y}_1 = \frac{16.75}{2} = 8.375\text{ mm}
    • Moment of area: Zp1=3350×8.375=28,056.25 mm3Z_{p1} = 3350 \times 8.375 = 28,056.25\text{ mm}^3
  • Bottom tension zone (below PNA):
    • Flange remaining: width 200 mm200\text{ mm}, thickness =20−16.75=3.25 mm= 20 - 16.75 = 3.25\text{ mm}. Area=200×3.25=650 mm2,yˉ=3.252=1.625 mm\text{Area} = 200 \times 3.25 = 650\text{ mm}^2, \quad \bar{y} = \frac{3.25}{2} = 1.625\text{ mm}
    • Web: width 15 mm15\text{ mm}, depth 180 mm180\text{ mm}. Area=2700 mm2,yˉ=3.25+1802=93.25 mm\text{Area} = 2700\text{ mm}^2, \quad \bar{y} = 3.25 + \frac{180}{2} = 93.25\text{ mm}
    • Moment of area: Zp2=(650×1.625)+(2700×93.25)=1,056.25+251,775=252,831.25 mm3Z_{p2} = (650 \times 1.625) + (2700 \times 93.25) = 1,056.25 + 251,775 = 252,831.25\text{ mm}^3
  • Total Plastic Section Modulus: Zp=Zp1+Zp2=28,056.25+252,831.25=280,887.50 mm3Z_p = Z_{p1} + Z_{p2} = 28,056.25 + 252,831.25 = \mathbf{280,887.50\text{ mm}^3}

Step 5: Shape Factor & Moments

  • Shape Factor: S=ZpZe=280,887.50157,264.54=1.786S = \frac{Z_p}{Z_e} = \frac{280,887.50}{157,264.54} = \mathbf{1.786}
  • Yield Moment: My=Ze⋅fy106=157,265×250106=39.32 kN-mM_y = \frac{Z_e \cdot f_y}{10^6} = \frac{157,265 \times 250}{10^6} = \mathbf{39.32\text{ kN-m}}
  • Fully Plastic Moment: Mp=Zp⋅fy106=280,888×250106=70.22 kN-mM_p = \frac{Z_p \cdot f_y}{10^6} = \frac{280,888 \times 250}{10^6} = \mathbf{70.22\text{ kN-m}} The plastic capacity is +78.6%+78.6\% higher than the yield capacity!

Example 2: Length of Plastic Hinge for 4 Structural Shapes

Problem Statement: A simply supported beam of span L=6.0 mL = 6.0\text{ m} is designed to reach its plastic collapse state under:

  • Condition 1: Concentrated load WW at midspan.
  • Condition 2: Uniformly distributed load ww over the entire span.

Compute the length of the plastic hinge LpL_p (in meters and as a percentage of span) for:

  1. Rectangular section (S=1.50S = 1.50)
  2. Solid circular section (S=1.698S = 1.698)
  3. Diamond section (S=2.00S = 2.00)
  4. Rolled I-section ISMB 400 (S=1.15S = 1.15)

Solution (Summary of Pre-Calculated Results):

Cross-SectionShape Factor SLp (Point Load)% of SpanLp (UDL)% of SpanRectangular Section1.5002.000 m33.3%3.464 m57.7%Solid Circular Section1.6982.466 m41.1%3.847 m64.1%Diamond Section2.0003.000 m50.0%4.243 m70.7%Rolled I-Section (ISMB 400)1.1500.783 m13.0%2.167 m36.1%\begin{array}{|l|c|c|c|c|c|} \hline \textbf{Cross-Section} & \textbf{Shape Factor } S & \textbf{$L_p$ (Point Load)} & \textbf{\% of Span} & \textbf{$L_p$ (UDL)} & \textbf{\% of Span} \\ \hline \text{Rectangular Section} & 1.500 & 2.000\text{ m} & 33.3\% & 3.464\text{ m} & 57.7\% \\ \text{Solid Circular Section} & 1.698 & 2.466\text{ m} & 41.1\% & 3.847\text{ m} & 64.1\% \\ \text{Diamond Section} & 2.000 & 3.000\text{ m} & 50.0\% & 4.243\text{ m} & 70.7\% \\ \text{Rolled I-Section (ISMB 400)} & 1.150 & \mathbf{0.783\text{ m}} & \mathbf{13.0\%} & \mathbf{2.167\text{ m}} & \mathbf{36.1\%} \\ \hline \end{array}

Key Engineering Conclusions:

  1. In rolled I-beams, the plastic hinge under a point load is extremely concentrated, extending over only 13.0%13.0\% of the span (783 mm783\text{ mm}), whereas in a diamond section it spans 50%50\% of the entire beam (3.0 m3.0\text{ m}).
  2. For all sections, a uniformly distributed load creates a plastic hinge zone that is 1.731.73 to 2.772.77 times longer than a concentrated load.

Example 3: Partially Plastified Rectangular Beam — Elastic Core Depth, Inelastic Bending Moment & Residual Stress Distribution

Problem Statement: A solid rectangular steel beam of width b=120 mmb = 120\text{ mm} and overall depth d=240 mmd = 240\text{ mm} is fabricated from Fe 410 steel with yield stress fy=250 MPaf_y = 250\text{ MPa} and Young's modulus E=200 GPaE = 200\text{ GPa}.

  1. Compute the elastic yield moment MyM_y and the fully plastic moment capacity MpM_p.
  2. When the section is loaded into the elasto-plastic range such that plasticity penetrates to a depth of 60 mm60\text{ mm} from both the top and bottom extreme fibers (leaving a central elastic core of half-depth ye=60 mmy_e = 60\text{ mm}), determine the applied elasto-plastic bending moment MM and the ratio ϕ/ϕy\phi / \phi_y of the curvature to the yield curvature.
  3. If the beam is subsequently unloaded elastically from its fully plastic state (M=MpM = M_p), calculate the magnitude and sign of the residual bending stresses at the extreme fiber (y=±120 mmy = \pm 120\text{ mm}) and at the neutral axis interface (y=0±y = 0^\pm).

Solution:

Step 1: Yield Moment (MyM_y) and Plastic Moment (MpM_p)

  • Elastic section modulus: Ze=bd26=120×(240)26=1.152×106 mm3Z_e = \frac{b d^2}{6} = \frac{120 \times (240)^2}{6} = \mathbf{1.152 \times 10^6\text{ mm}^3}
  • Plastic section modulus: Zp=bd24=120×(240)24=1.728×106 mm3(S=Zp/Ze=1.500)Z_p = \frac{b d^2}{4} = \frac{120 \times (240)^2}{4} = \mathbf{1.728 \times 10^6\text{ mm}^3} \quad (S = Z_p / Z_e = 1.500)
  • Yield and Plastic Moments: My=fyZe=250×1.152×106×10−6=288.00 kN⋅mM_y = f_y Z_e = 250 \times 1.152 \times 10^6 \times 10^{-6} = \mathbf{288.00\text{ kN}\cdot\text{m}} Mp=fyZp=250×1.728×106×10−6=432.00 kN⋅mM_p = f_y Z_p = 250 \times 1.728 \times 10^6 \times 10^{-6} = \mathbf{432.00\text{ kN}\cdot\text{m}}

Step 2: Elasto-Plastic Bending Moment and Curvature Ratio (ye=60 mmy_e = 60\text{ mm})

  • With half-depth d/2=120 mmd/2 = 120\text{ mm} and elastic core half-depth ye=60 mmy_e = 60\text{ mm}, the normalized elastic core ratio is: yed/2=60120=0.500\frac{y_e}{d/2} = \frac{60}{120} = 0.500
  • From the elasto-plastic moment-curvature relation derived in Section 9 (Derivation 1): M=Mp[1−13(yed/2)2]=432.00[1−13(0.500)2]=432.00[1−112]=432.00×1112=396.00 kN⋅mM = M_p \left[ 1 - \frac{1}{3}\left(\frac{y_e}{d/2}\right)^2 \right] = 432.00 \left[ 1 - \frac{1}{3}(0.500)^2 \right] = 432.00 \left[ 1 - \frac{1}{12} \right] = 432.00 \times \frac{11}{12} = \mathbf{396.00\text{ kN}\cdot\text{m}} (Direct equilibrium verification: Elastic core moment Mcore=fyb(2ye)26=250×120×12026×10−6=72.00 kN⋅mM_{\text{core}} = f_y \frac{b (2 y_e)^2}{6} = 250 \times \frac{120 \times 120^2}{6} \times 10^{-6} = 72.00\text{ kN}\cdot\text{m}; Plastic outer shells moment Mshell=2[fyb(120−60)(60+602)]×10−6=2[250×120×60×90]×10−6=324.00 kN⋅mM_{\text{shell}} = 2 \left[ f_y b (120 - 60) \left(60 + \frac{60}{2}\right) \right] \times 10^{-6} = 2 [250 \times 120 \times 60 \times 90] \times 10^{-6} = 324.00\text{ kN}\cdot\text{m}; Total M=72.00+324.00=396.00 kN⋅mM = 72.00 + 324.00 = \mathbf{396.00\text{ kN}\cdot\text{m}}).
  • Curvature ratio relative to first yield: ϕϕy=d/2ye=12060=2.00\frac{\phi}{\phi_y} = \frac{d/2}{y_e} = \frac{120}{60} = \mathbf{2.00} (Doubling the yield curvature develops 396.00/432.00=91.67%396.00 / 432.00 = 91.67\% of the full plastic moment capacity!)

Step 3: Residual Stresses After Elastic Unloading from Mp=432.00 kN⋅mM_p = 432.00\text{ kN}\cdot\text{m}

  • Elastic unloading from MpM_p superimposes a reverse linear elastic stress distribution of peak magnitude: σunload, max=MpZe=S⋅fy=1.500×250=375.00 MPa\sigma_{\text{unload, max}} = \frac{M_p}{Z_e} = S \cdot f_y = 1.500 \times 250 = \mathbf{375.00\text{ MPa}}
  • At the Extreme Compression/Tension Fibers (y=±120 mmy = \pm 120\text{ mm}): σr,extreme=σplastic−σunload=±250.00∓375.00=∓125.00 MPa(∓0.50fy)\sigma_{r,\text{extreme}} = \sigma_{\text{plastic}} - \sigma_{\text{unload}} = \pm 250.00 \mp 375.00 = \mathbf{\mp 125.00\text{ MPa}} \quad \left(\mp 0.50 f_y\right)
  • At the Neutral Axis Interface (y=0±y = 0^\pm): σr,NA=±250.00−0=±250.00 MPa(±1.00fy)\sigma_{r,\text{NA}} = \pm 250.00 - 0 = \mathbf{\pm 250.00\text{ MPa}} \quad \left(\pm 1.00 f_y\right)

(The locked-in residual stress field is self-equilibrating with zero net axial force and zero net bending moment).


11. Exam Traps, Common Pitfalls & Code Nuances

Trap 1: Confusing ENA and PNA in Asymmetric Sections

  • The Trap: Students frequently compute ZpZ_p by finding the centroid (ENA) and taking moments of area about it.
  • The Reality: For unsymmetrical sections (T-sections, channels, unequal angles), ENA ≠\ne PNA. You must FIRST locate the Equal Area Axis (A1=A2=A/2A_1 = A_2 = A/2) to establish the PNA, and THEN take moments of area about that specific PNA.

Trap 2: Memorizing Shape Factors Inverted

  • Shape factor is always ≥1.0\ge 1.0: S=ZpZe=MpMy≥1.0S = \frac{Z_p}{Z_e} = \frac{M_p}{M_y} \ge 1.0 Never invert this ratio (Ze/Zp≤1.0Z_e / Z_p \le 1.0).

Trap 3: Direct Comparison of Profile Plastic Efficiencies

  • A common exam multiple choice question asks: "Which of the following sections has the HIGHEST shape factor?"
    • (A) I-Section (S≈1.15S \approx 1.15)
    • (B) Rectangle (S=1.50S = 1.50)
    • (C) Circle (S=1.70S = 1.70)
    • (D) Diamond (S=2.00S = 2.00)
  • Correct Answer: Diamond (S=2.00S = 2.00), or Triangle (S=2.34S = 2.34) if listed!
  • Common Confusion: Students often confuse elastic structural efficiency with shape factor. An I-section is the most elastically efficient shape (material placed at extreme fibers), which is precisely why its shape factor is the lowest! A diamond is elastically inefficient, giving it a massive reserve factor (S=2.0S = 2.0).

Trap 4: Plastic Hinge Formula Inversion for Point Load vs UDL

  • Point Load: Lp=L(1−1S)L_p = L \left(1 - \frac{1}{S}\right) (No radical!).
  • UDL: Lp=L1−1SL_p = L \sqrt{1 - \frac{1}{S}} (Square root present!).

12. Official Exam Practice Questions

Question 1 (GATE CE)

A mild steel solid circular shaft of diameter DD is subjected to pure bending. The ratio of its plastic moment capacity MpM_p to its yield moment capacity MyM_y is:

  • (A) 1.501.50
  • (B) 16/(3π)16 / (3 \pi)
  • (C) 4/π4 / \pi
  • (D) 2.002.00

Detailed Solution:

  • Ze=πD332Z_e = \frac{\pi D^3}{32}
  • Zp=D36Z_p = \frac{D^3}{6}
  • Shape Factor S=ZpZe=D3/6πD3/32=326π=163π≈1.698S = \frac{Z_p}{Z_e} = \frac{D^3 / 6}{\pi D^3 / 32} = \frac{32}{6 \pi} = \frac{16}{3 \pi} \approx 1.698.
  • Correct Answer: (B)

Question 2 (UPSC ESE)

For a simply supported beam of rectangular cross-section carrying a central concentrated load, the length of the plastic hinge formed at collapse is:

  • (A) L/2L / 2
  • (B) L/3L / 3
  • (C) L/3L / \sqrt{3}
  • (D) L/4L / 4

Detailed Solution:

  • For a concentrated load, Lp=L(1−1/S)L_p = L (1 - 1/S).
  • For a rectangular section, S=1.50=3/2  ⟹  1/S=2/3S = 1.50 = 3/2 \implies 1/S = 2/3.
  • Lp=L(1−2/3)=L/3L_p = L (1 - 2/3) = L / 3.
  • Correct Answer: (B)

Question 3 (SSC JE)

The shape factor of a diamond section with vertical and horizontal diagonals is:

  • (A) 1.50
  • (B) 1.70
  • (C) 2.00
  • (D) 2.34

Detailed Solution:

  • For a diamond (rhombus), Zp=bd2/12Z_p = b d^2 / 12 and Ze=bd2/24Z_e = b d^2 / 24.
  • S=24/12=2.00S = 24 / 12 = 2.00.
  • Correct Answer: (C)

Question 4 (State AE / RRB JE)

According to IS 800:2007, plastic design of a steel structure is permitted only if the material possesses a minimum ductility ratio (ϵu/ϵy\epsilon_u / \epsilon_y) of at least:

  • (A) 2.0
  • (B) 4.0
  • (C) 6.0
  • (D) 10.0

Detailed Solution:

  • Per IS 800:2007 Section 8, the material must possess a ductility ratio μd=ϵu/ϵy≥6.0\mu_d = \epsilon_u / \epsilon_y \ge 6.0.
  • Correct Answer: (C)

Question 5 (UPSC ESE Conventional)

Derive the expression for the length of the plastic hinge in a simply supported beam of span LL carrying a uniformly distributed load ww at collapse. Calculate the numerical value of LpL_p for an I-section with S=1.15S = 1.15 on a span of 8.0 m8.0\text{ m}.

Detailed Solution:

  1. Derivation:
    • At collapse, the midspan moment reaches Mp=wL2/8M_p = w L^2 / 8.
    • The bending moment equation is M(x)=wL2x−wx22M(x) = \frac{w L}{2} x - \frac{w x^2}{2}.
    • At the extremities of the plastic hinge, M=My=Mp/SM = M_y = M_p / S.
    • Equating: wL2x−wx22=wL28S  ⟹  4x2−4Lx+L2S=0\frac{w L}{2} x - \frac{w x^2}{2} = \frac{w L^2}{8 S} \implies 4 x^2 - 4 L x + \frac{L^2}{S} = 0.
    • Solving for xx: x=L2[1−1−1/S]x = \frac{L}{2} \left[1 - \sqrt{1 - 1/S}\right].
    • The length of the plastic hinge is the distance between these two symmetric points: Lp=L−2x=L−L[1−1−1/S]=L1−1SL_p = L - 2 x = L - L \left[1 - \sqrt{1 - 1/S}\right] = L \sqrt{1 - \frac{1}{S}}
  2. Numerical Evaluation:
    • Span L=8.0 mL = 8.0\text{ m}, S=1.15S = 1.15.
    • 1/S=1/1.15=0.86961/S = 1 / 1.15 = 0.8696.
    • 1−1/S=1−0.8696=0.13041 - 1/S = 1 - 0.8696 = 0.1304.
    • Lp=8.0×0.1304=8.0×0.3611=2.889 mL_p = 8.0 \times \sqrt{0.1304} = 8.0 \times 0.3611 = \mathbf{2.889\text{ m}}.